Fuse Position to Activate Accessory Power and Brake Control Power on a 2008 Chevy Avalanche
Question:
Can you define the actual fuse positions in the fuse box that activiate the accessory power and brake control power on 2008 Avalanche. I have installed my Prodigy brake controller per the instructions on your site and although my brake controller has power, when I connect to my trailer I get no signal to the trailer brakes. When I actvate the manual brake lever on the prodigy, I get the NC in display No connection even though I am plugged into the trailer.
asked by: David
Expert Reply:
If my memory serves me right the fuse positions for the auxiliary power posts under the dash on a 2008 Chevrolet truck or SUV are the closest two square fuse slots in the front end of the power distribution box, see photo link. The best way to test those power posts is to use a circuit tester, item # PTW2993, if needed. Ground the lead from the tester and touch each power post independently. If the tester lights, then the fuse is in the proper location. If not, a square fuse should be inserted. Once the fuse is installed in the correct slot the stud will be hot.
The fuse box lid normally has a legend underneath it stating the proper fuse location and size. This should help you out also.
Since you say that you have power to the brake controller, it sounds like the fuse is in place. If this is the case there are several things you will need to check. The N.C. reading indicates that the brake controller is not sensing a connection to the trailer brake magnets.
Start with checking the truck and trailer connector. Open them up and look inside the connectors. If you find a loose wire shorting to the trailer brake feed or corrosion inside the connector, this could be the issue. Fix any mis-wiring, see link to trailer connector diagrams, and clean out the connectors if any corrosion is found. Some dielectric grease, # 11755, will help prevent corrosion and would be a good idea to use on the connections while you have the connector open. If you determine that you need a new connector, the Pollack 7-Way RV connector, # PK11916, would most likely be the correct choice for your truck. For the trailer the Pollack 7-Way RV connector, # PK12706, would most likely be correct.
Next, check the ground wire for the brake controller, at the trailer tongue, and at the back of the vehicle and make sure they are grounded properly to a clean rust, paint and primer free portion of the vehicle and/or trailer frame. Also, make sure one wire from each brake magnet is grounded properly either to the ground wire from the trailer connector or to the trailer frame.
Next, check the brake feed power wire to be sure there is not an open circuit on this wire. Check all the way back to the brake magnet connections. If the wire is pinched frayed or broken and contacting the trailer frame or another wire, correct any of these issues.
You should find the issue using these troubleshooting measures.
Products Referenced in This Question
Dielectric Grease for Electrical Connectors, 2 oz.
- Accessories and Parts
- Trailer Wiring
- Wiring
- Dielectric Grease
- LubriMatic
more information >
Twist-in, 7-Pole, RV-Style Trailer Connector for Chevy and GMC Vehicles - Vehicle End
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 7 Round - Blade
- Pollak
more information >
Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- Plug Only
- 7 Round - Blade
- Pollak
more information >
Product Page this Question was Asked From
Continue Researching
- Article: Installing an Electric Brake Controller on 2007-2013 GM Full-Size Truck or 2007-Present GM SUV
- Q&A: Location of Fuses In Power Distribution Box To Install Brake Controller on 2008 Chevrolet Silverado
- Q&A: Troubleshooting No Power to Brake Controller 12 Volt Power Wire On a 2013 Chevrolet Avalanche
- Shop: Pollak 7-Way to RV Socket LED Circuit Tester - Vehicle End
- Video: Pollak 7-Way to RV Socket LED Circuit Tester Review
- Shop: Brake Controller
- Q&A: Installing a Brake Controller on a 2007 Chevy Avalanche With or Without a Factory Tow Package
- Q&A: Replacement Trailer Grease Seals for Allis 5013 29772
- Shop: Trailer Hitch
- Video: Choosing the Right Brake Controller
- Search Results: 44649
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: Replacement Hub for 2013 Wildwood 26TBSS Hub Drum with AL-KO 8700
- Article: Trailer Wiring Diagrams
- Search Results: 68149
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: 25580
- Shop: Suspension Enhancement
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Gooseneck Hitch
- Video: etrailer Magnetic Hitch Receiver Reducer Sleeve Review
- Shop: Redarc Tow-Pro Elite Brake Controller - Dash Knob - 2 Braking Modes - 1 to 3 Axles - Proportional
- Search Results: dust cap
- Q&A: How To Setup a 2019 Jeep Cherokee Trailhawk for Flat-Towing