Coupler Latch Adjustability on Demco Brake Actuating Coupler # 8605001
Question:
Hello, I see in the pictures and on my coupler there is lock tight on the threads underneath on the coupler lock. Is this lock tab adjustable? Should the lock tab be completely underneath the ball? My coupler lock tab sits about 3/4 of the way down the ball.
asked by: SGT
Helpful Expert Reply:
The coupler latch assembly shown in the attached dimension photo shows the latch in the open position of # 8605001. When the coupler trigger latch is closed the wedge simply needs to be on the underside of the hitch ball. As long as you can't lift the coupler off of the ball and the connection stays secure, your coupler latch is working correctly. 3/4 of the way down the hitch ball is about right in most cases.
If there is not a good connection meaning you can lift the coupler while the latch is locked and get a clank or if the connection allows you to completely lift the coupler off when the trigger latch is locked, then you will need to adjust the latch for proper connection with the nut on the underside of the coupler.
The newest model of the # 8605001 is the # DM72VR.
Product Page this Question was Asked From
Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Straight Tongue Coupler
- Bolt-On
- 7000 lbs GTW
- 2 Inch Ball Coupler
- Drum Brakes
- No Lockout
- Demco
more information >
Continue Researching
- Shop: Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Search Results: trailer brakes
- Shop: Dexter Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 6,000 lbs
- Shop: Dexter Zinc-Plated Brake Actuator - Drum - Multi-Fit Ball - Bolt On - 7,000 lbs
- Search Results: surge brake actuator
- Search Results: trailer breakaway kit
- Q&A: Can I Use Shims or Washers to Close the Gap Between Trailer Tongue and Demco Hydraulic Actuator
- Q&A: Correct Replacement for Demco DA66B Hydraulic Trailer Brake Actuator
- Q&A: Would Demco Brake Actuator Be Proper Replacement for Tie Down Engineering Model 660
- Q&A: Bolt Hole Dimensions Of Demco Brake Actuator # DM8669112
- Shop: Dexter DX7.5L A-60 Brake Actuator with Fill Cap - Bolt On - Drum - 2" Ball - Zinc - 7,500 lbs
- Shop: Demco Hydraulic Brake Actuator w/ Drop - Drum - Zinc - 2" Ball - 8,000 lbs
- Shop: Dexter DX7.5 Drop-N-Go Brake Actuator - Drum Brakes - 2" Ball - Zinc Plated - 7,500 lbs
- Video: Review of Demco Brake Actuator - Surge Brake Actuator - DM72VR
- Video: Demco Hydraulic Brake Actuator Review
- Search Results: hydraulic drum brakes
- Search Results: trailer coupler
- Q&A: Recommended Bolt On A-Frame Trailer Coupler For A Jayco Pop-Up Camper
- Q&A: Solution for Needing Replacement 2 inch Ball Belcrank Surge Coupler
- Q&A: Titan T4500600 Brake Actuator Dimensions
- Shop: etrailer Trailer Coupler Lock for Flat Lip 2-5/16" Ball Coupler - Aluminum - Silver
- Video: Dexter Left and Right Electric Trailer Brake Kit Installation
- Video: Demco Hydraulic Brake Actuator Reverse Lockout Solenoid Kit Installation
- Search Results: break away wiring
- Search Results: trailer wiring
- Article: Parts Required to Add Electric Over Hydraulic Drum Brakes to a Trailer
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Trailer Wiring Diagrams
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Hitch