Does Yates Ribbed Wobble Roller for EZ Loader Boat Trailers # YR500YW-8PEZ Include Mounting Brackets

Question

Question:

Do mounting brackets come with

asked by: Charles W

0

Expert Reply:

Yates Ribbed Wobble Roller for EZ Loader Boat Trailers # YR500YW-8PEZ does not come with brackets. This roller was designed for EZ Loader Boat Trailers and fits a 1 inch diameter shaft. Those items you would need to obtain from EZ Loader since the largest shaft diameter we have is 5/8 inches.

expert reply by: Michael H

0

Answer 1

We have the Yates Ribbed Wobble Roller for EZ Loader Boat Trailers #YR500YW-8PEZ which has a 1-1/8" inside length. This is the only wobble roller that says it is less than 1-1/2" inside length.

view full answer...

Answer 2

The Yates Ribbed Wobble Roller, #YR500YW-8PEZ, is exactly what you need for your 1999 EZ Loader boat trailer. The bushings are included with this roller. For a hog ring, we offer part #CE10981 and you can use part #SW1000 for a washer. At this…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5…

view full answer...

Answer 11

According to Lippert, the mounting nuts should be torqued to 120 ft-lbs for the Axle Riser Kit - Single Square Torsion Axle - 3-1/2" Lift #LC382741.

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Does Yates Ribbed Wobble Roller for EZ Loader Boat Trailers # YR500YW-8PEZ Include Mounting Brackets

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching