Can Valterra RV Waste Valve # T11 be Mounted Horizontally

Question

Question:

Can this valve be mounted horizontally versus vertically?

asked by: Bruce L

1

Helpful Expert Reply:

Valterra RV Waste Valve # T11 can be installed horizontally. We state to position the valve at the desired angle during installation which would indicate it could technically be placed at any angle. For installation I do recommend some ABS solvent # A05-0303 if you do not already have some.

expert reply by: Michael H

1

Answer 1

Thank you for the photo of your RV's P-trap. We offer one RV plumbing P-trap, Valterra RV Sewer P-Trap #D50-2215 that you referenced in your question, which is detailed in the linked photo. This part uses 1-1/2-inch fittings and installs…

view full answer...

Answer 2

According to Valterra, you should use a non-hardening sealant safe for ABS plastic for the Replacement RV Toilet Floor Flange #T05-0784. So you would not want to use Rectorseal #5 because it is not supposed to be used on ABS. You will just want to…

view full answer...

Answer 3

For A Dometic 320 Toilet, you can use the Replacement RV Toilet Floor Flange #T05-0784 to replace your broken flange.

view full answer...

Answer 4

You can just use a replacement flange like the LaSalle Bristol Toilet Floor Flange for RV #344633633. You'll have to cut out the only flange and will most likely need to add a bit more straight pipe to glue into the hub of this flange. If…

view full answer...

Answer 5

Yes, the Replacement RV Toilet Floor Flange #T05-0784 has the standard 4" diameter opening and 3" FPT (Female Pipe Thread) that will match what you have with your Canplas 3634-5 flange. Attached is a review video for you to check…

view full answer...

Answer 6

I believe I have a solution for you. What you can do is use the LaSalle Bristol Toilet Floor Flange w/ Spigot for RV #3446336347 with the Valterra DWV Adapter for RV Sewer System - ABS Plastic #D50-2929. The #3446336347 is 1-1/2" tall but…

view full answer...

Answer 7

That's a good question but we don't have a way to look that up since Winnebago does not list that as a spec anywhere. You'd have to measure and verify before ordering either the 3 inch #F02-2106 or the larger size #F02-2103.…

view full answer...

Answer 8

If you want to install the Valterra Waste Valve #T58 in the side position it will absolutely acceptable, yes. In fact, the accompanying photo shows it installed in the same way as you are asking about. I've also added a link to a video review…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side.…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Can Valterra RV Waste Valve # T11 be Mounted Horizontally

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching