Trailer Hitch and Trailer Wiring for a 2011 Chevy Cruze to Tow a Jet Ski
Question:
i have a 2011 chevy cruze and want to tow a jet ski trailer wanting to know how the Draw-Tite would conect to car and how to hook up lights to trailer thanks for ur time
asked by: Steven B
Expert Reply:
The Draw-Tite Trailer Hitch, # 24882, will bolt to the bottom of your 2011 Chevy Cruze using factory holes in the frame rails. While there is no drilling needed, you might need to enlarge an existing access hole in order to fish the hardware through to bolt on the hitch. I have included a link to the installation instructions for the hitch for you to view.
The hitch does not com with a ball mount. You will need # 3593. You will also need a ball and trailer wiring to complete the towing set up. For a ball, you can use # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter) depending on what the Jet Ski trailer coupler requires.
The correct trailer wiring for your vehicle is the T-One Connector w/Upgraded Circuit Protected ModuLite, # 118508. There are 4 connections that need to be made to install this wiring harness. One behind each tail light, a ground, and a connection to the positive battery terminal via the included fuse and fuse holder. A connection to the battery is required to provide power to the converter which also supplies most of the power to the trailer lights. This protects the electrical components of the vehicle.
I have included a link to the installation instructions for the wiring as well.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Wiring Diagrams
- Article: My Trailer Hitch Doesn't Fit
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Is There Custom Towed Vehicle Wiring Available For A 2011 Chevy Cruze LS
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Trailer Hitch and Wiring for a 2014 Chevy Cruze Diesel Towing a Seadoo Spark PWC
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Width of Curt Class V Trailer Hitch # C15317
- Q&A: Recommended Hitch for a 2024 Subaru Legacy
- Q&A: What is the Difference Between Class 1 and Class 2 Hitches for the Scion XB
- Q&A: Will the Draw-Tite Sportframe Hitch 24882 Fit a 2015 Chevrolet Cruze LTZ
- Article: Trailer Hitch Receiver Sizes
- Article: Flat Towing Package for 2016-2018 Ford Focus