Timbren Axle Less Setup for Trailer with 4 inch Lift and Surge Brake Compatible

Question

Question:

I am looking to replace my suspension on my 1972 Amerigo fiberglass RV. 16ft, 2000lbs unladened weight, current tongue weight is less than 300. I have been looking at Timbren axle less systems. I want a 4 inch lift, due to rough country camping, but I only see a straight and a 4inch with electric brake hubs. I prefer electric over drum, but prefer a lift over electric if that is the only option. Are the drums electric or hydraulic/inertia style? Basically, what is/are my best options Google Amerigo FG16 to see how close to the ground they ride.

asked by: Dan C

0

Expert Reply:

Best option would be the Timbren Axle Less kit part # ASR35HDS05 which has a 3,500 lb capacity and has a 4 inch lift built into it. It has brake flanges on the spindle already too so all you need to do is attach the hydraulic style of assemblies you want as well as install the hub/drums.

For a hub you'd need the part # 8-201-9UC3-EZ and for brake assemblies part # AKFBBRK-7R for the right hand side and part # AKFBBRK-7L for the left hand side.

expert reply by: Jameson C

0

Answer 1

We have the Timbren Axle-Less Trailer Suspension System #ASR3500S06 which has a 4" lift spindle with brake flange and will allow you to have a 5 on 4-1/2" bolt pattern. For the brakes we have either the Disc Kit #KOD59FR if you are wanting…

view full answer...

Answer 2

It sounds like you are referring to surge brakes in which case I do have an option for you to add these to the Timbren Axle-Less Trailer Suspension System part #ASR1THDS03. In order to do this you will need the Demco Hydraulic Brake Kit part…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Timbren Axle Less Setup for Trailer with 4 inch Lift and Surge Brake Compatible

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching