Dimensions of Timbren Rear Suspension Jounce Spring TFR250SDG for 2011 Ford F-250

Question

Question:

2011 f250 2WD gas What is total height of #TFR250SDG Including bracket and spring Thanks My opening is 8

asked by: Kevin B

0

Expert Reply:

On Timbren rear axle jounce spring kit # TFR250SDG the brackets are 3-inches tall and the spring itself is 4-1/2-inches tall. These offer no-drill installation in your 2011 F-250 2WD gasser as shown in the linked video.

expert reply by: Adam R

0

Answer 1

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 2

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 3

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 4

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 9

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Dimensions of Timbren Rear Suspension Jounce Spring TFR250SDG for 2011 Ford F-250

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching