Does Lets Go Aero Hitch Pin Lock part # 63232 Have Weight Capacity

Question

Question:

Is there tow limit using the Anti-Rattle Trailer Hitch Receiver Lock for 2inch Hitches - 2-5/8inch Span Item # 63232? Thanks

asked by: Joel R

0

Expert Reply:

HItch pins like the Lets Go Aero hitch pin lock part # 63232 that you referenced do not have towing capacities as they do not typically ever carry the full weight of the trailer. As long as you aren't exceeding the capacity of the hitch you are using this lock with you'll be fine.

expert reply by: Jameson C

0

Answer 1

For your Yakima HoldUp 2 Bike Rack for 1-1/4" Hitches - Platform Style - Tilting #Y02445, the Replacement 2" Hitch Adapter for Yakima Carriers #Y8890174 will not work according to my contact at Yakima and it is no longer available. Instead…

view full answer...

Answer 2

The MaxxTow Anti-Rattle Clamp has not been tested or rated for use when towing a trailer. Because of that it should only be used for hitch mounted accessories such as bike racks or cargo carriers. So basically, since they have not tested it for…

view full answer...

Answer 3

Actually the term flat towing refers to towing a vehicle behind another vehicle with 4 wheels on the ground. If you aren't familiar with flat towing I can easily see how you drew that conclusion. I attached a help article on flat towing for you…

view full answer...

Answer 4

The Curt Cargo Carrier for 2" Hitches - Steel - Folding #C18152 has a 500 lb weight capacity so it absolutely has the needed capacity to hold your 250 lb holding tank. If you were asking about the capacity of the trailer hitch itself on your…

view full answer...

Answer 5

From what I have found you're talking about the Curt Anti-Rattle Kit for Hollow Shank Accessories #C69HR, #C22321, and #F-315. The #C22321 and #C69HR are both for a 2" hitch but the #C22321 fits a receiver with a 5/8" pin hole while the…

view full answer...

Answer 6

Yes, the Curt Anti-Rattle Kit for Hollow Shank #C69HR will hold up when pulling your equipment trailer. This will only work on ball mounts for a 2" receiver with a hollow shank. I feel the Blue Ox Hitch Receiver Immobilizer II #BX88224 is the…

view full answer...

Answer 7

There is an SKS lock end that works with the #8890260 with the part #Y07235 but by the time you add up the cost of both parts you are better off going with a similar universal setup like the #63232 since the price is better and would work just as…

view full answer...

Answer 8

If you have a hollow shank ball mount you can use this anti rattle device #C69HR. One part will insert into the ball mount shank and you can use the threaded pin to take out the excessive rattling you're experiencing.

view full answer...

Answer 9

It sounds like you are actually talking about part #8890260 with the pin and anti-rattle nut and housing. On the outside of the rack shank close to the end you will see 2 holes with part of the black plastic nut housing in them. These hold the nut…

view full answer...

Answer 10

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt and is the same bolt that comes with the part #8890260. The size wrench you would use to install or remove this bolt is 15/16…

view full answer...

Answer 11

The Curt RockerBall Anti-Rattle Towing Kit #C43KR takes the additional height of the base of the RockerBall into account for the listed 4" rise and 5" drop. I have attached an image below showing how it is measured. Typically, you find the…

view full answer...

Answer 12

The Class III Curt trailer hitch part #C13418 that you referenced has a 5/8 inch diameter hitch pin hole which is standard for the 2 inch hitch size. So the Curt anti-rattle device 22323 part #C69HR would fit.

view full answer...

Does Lets Go Aero Hitch Pin Lock part # 63232 Have Weight Capacity

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching