Reviews of Snap & Zap Towing Mirrors Causing Paint Damage

Question

Question:

Hello, I am inquiring about your K-Source Snap and Zap Custom Towing Mirrors - Snap On - Driver and Passenger Side Item # KS80710 for my 2016 Ram 2500. Have you received any reports of the mirror actually damaging the paint on the OEM mirrors?

asked by: Marcello

1

Helpful Expert Reply:

We haven't heard of anyone having an issue with the Snap & Zap towing mirrors, part # KS80710, causing any damage to paint. In fact, the reviews on them are very positive. The biggest complaint I see is that there is some vibration but not enough to cause a problem using them

expert reply by: Charles S

1

Answer 1

Suspension enhancement may help you, but first I would make sure that your Weight Distribution system is rated and set up correctly. If it is, then you can go with some sort of suspension enhancement. Both the Timbren #TGMRCK15S and the SumoSprings…

view full answer...

Answer 2

The 3,000lb SumoSprings Rebel Custom Helper Springs #SS95QR will provide more support to reduce the amount of sag that you are having with your dump trailer. Both the Rebel and 1,500lb SumoSprings Solo Custom Helper Springs #SSR-117-47 will perform…

view full answer...

Answer 3

If you have a tandem axle travel trailer that weighs 6,000 lbs a Load Range C tire like the part #AM1ST92 would work, but since you said that is the weight when empty you would most likely want to go with the Load Range D just to be safe. For that…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Reviews of Snap & Zap Towing Mirrors Causing Paint Damage

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching