High Capacity Trailer Hitch Recommendation for 1997 Chevy Suburban

Question

Question:

Will this fit a 1997 suburban

asked by: James B

0

Expert Reply:

We have a Class IV that does fit a 1997 Chevy Suburban but it is not the B and W you mentioned. Instead you'd want the Curt hitch part # C14029 which is a confirmed fit and would work well. This has a 10,000 lb towing capacity which would be more than you'd need.

expert reply by: Jameson C

0

Answer 1

The Class lV or V hitches we have that are available for your 2003 Newmar Dutch Star RV require welding installations. I recommend the Curt Class V Universal Weld-on Hitch, part #15901. This will fit frames from 18 up to 44 inches, and with the side…

view full answer...

Answer 2

The distance from the bottom of the frame to the top of the 2" receiver of the B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2" #BWHDRH25198 you were looking at is 7-3/8" as shown in the included diagram. I…

view full answer...

Answer 3

The Hole spacing for the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25198 are as follows(all measurements are for center of hole to center of hole). 34" Width Frame -Front holes- 28-7/8" -Middle and rear holes- 29-1/2"…

view full answer...

Answer 4

When looking at replacement tires for your 2018 Forest River Trailer, you will want to make sure that they will provide you with a combined load capacity that matches or, ideally, exceeds the possible loaded weight of the trailer. You will also want…

view full answer...

Answer 5

For your 2004 Newmar Dutch Star Class A motorhome you can use one of the 2-inch RV-rated trailer hitches shown on the linked page. We offer both bumper-mount and frame-mount hitches and the better option is usually the frame-mounted type like #C13701…

view full answer...

Answer 6

The B&W Class V trailer hitch receiver you referenced, their part #BWHDRH25122, is not a correct fit for your 1997 Chevy K1500 step-side pickup with factory step bumper. This hitch is intended for the cab-and-chassis version of your truck. But we…

view full answer...

Answer 7

I have attached a photo of the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25198 you asked about. I have noted the mounting holes on the photo you can check out. The distance center-to-center from the front mounting hole to the second is…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

High Capacity Trailer Hitch Recommendation for 1997 Chevy Suburban

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching