Recommendation to Upgrade to Dual Motor Landing Gear System on Trailer
Question:
Looking to do a dual power landing gear setup, Vmc900l-320105 are the numbers on the following leg. Can I just buy a rebuild for a lead leg and install it in a following leg and which rebuild kit will work?
asked by: Mitchall B
Expert Reply:
In order to upgrade your existing landing gear system to a dual motor setup, I recommend completely replacing the follower leg with a lead leg # LG-177202. I have attached the dimensions for this lead leg so you can compare them to your existing unit to make sure it will work well as a replacement. It's technically possible to upgrade the follower leg by replacing all of its inner components, but this is extremely involved and it is much safer to simply replace the leg itself.
On a dual motor setup, the two legs will not be attached to each other, so you will also need to add a Gearbox # LG-179015, and Motor # LG-217884.
Since you would be creeping up towards the cost of a brand new, dual-motor system, I recommend considering a entirely new setup with the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. These dual electric jacks feature a combined weight capacity of 12,000 pounds with a retracted height of 36 inches and an extended height of 74 inches. The distance from the top of motor to the first weld point is 8-1/2 inches.
Products Referenced in This Question
Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gearbox
- Stromberg Carlson
more information >
Motor and Switch Kit for Stromberg Carlson Landing Gear - 5,500 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Motor
- Stromberg Carlson
more information >
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- Landing Gear
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Replacement Lead Leg for Stromberg Carlson Landing Gear - 33-1/2"
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Shop: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set
- Shop: Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Video: etrailer Landing Gear Set Review
- Shop: Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Q&A: How To Upgrade To a Dual Motor Landing Gear Set On a Forest River 35' 5th Wheel
- Shop: Replacement Lead Leg for Stromberg Carlson Landing Gear - 33-1/2"
- Video: Review of Ultra-Fab Products Camper Jacks - Landing Gear - UF17-943010
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC141893
- Q&A: Replacement Motor for Lippert Model 1-065-041012-01 Landing Gear
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: 68149
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Article: Trailer Tire Sizing
- Search Results: 25580
- Shop: Fifth Wheel Hitch
- Video: Lippert Solera Slider Slide-Topper Review
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Search Results: dust cap
- Shop: Suspension Enhancement
- Q&A: How to Tell If MORryde Rubber Equalizers Will Fit Trailer