Replacement 5th Wheel Lead Landing Gear Leg for 2011 Keystone Cougar

Question

Question:

I have a 2011 Keystone Couger 5th The Lead Jack screw is seizing. Is the following the correct part # ? Replacement Lead Jack w/ Leg for Stromberg Carlson Landing Gear - Item # LG-179013

asked by: Henry F

0

Expert Reply:

You are correct that Lippert part # LC179013, their 5th Wheel RV Landing Gear Lead Leg, is the correct part to replace the damaged unit on your 2011 Keystone Cougar.

expert reply by: Adam R

0

Answer 1

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if it…

view full answer...

Answer 2

What you have is a standard Lippert style of RV landing gear which we can easily match you with a replacement for. The Stromberg Powered Landing Gear part #LG-1 would fit what you have as an exact replacement and would work well.

view full answer...

Answer 3

The correct landing gear set for your 2011 Keystone RV Cougar Fifth Wheel Series M-244 RLS should be the Lippert Electric Landing Gear Set part #LC333964. In order to make sure you will want to take a quick measurements from the outside edge of each…

view full answer...

Answer 4

The Replacement Ball Assembly #UF19-001057 that you referenced can be used with an Andersen Ultimate fifth wheel adapter but it has to be used with an Ultra Fab stabilizer like the #UF19-950500 since we can't guarantee it would work on an EAZ…

view full answer...

Answer 5

If the landing gear set you have on your Forest River is a Bulldog setup the motor of it would fit on the Bulldog #BD500162 but if instead you have the more standard brands of Venture, Stromberg, LCI, or Lippert you'd want the #LC333966.

view full answer...

Answer 6

All weight distribution system parts, except for the shank component that fits into your hitch, are proprietary and brand-specific. You could mount a Curt WD head on a Reese shank (or the reverse) but the spring bars and other parts need to be from…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Replacement 5th Wheel Lead Landing Gear Leg for 2011 Keystone Cougar

Product Page this Question was Asked From

Continue Researching