Is a Gap Between a Trailer Brake Backing Plate and Drum Normal
Question:
hI,I ordered all four new brake plates and four drums and i installed the brake backing plates to the 5 bolt flange and installed the assembled drum over the shoes and i torqued the spindle nut to 50 ft. pnds. and then backed it off after pre load, I am seeing now that theres almost a half inch of space between the backing plate and the back face of the drum and i can see the shoes slightly when looking through the gap. It seem like the backing plate or mounting plate should be forward almost that half inch or the magnet will also be further away from the armature. Please let me know what your thoughts are.
asked by: Tom B
Expert Reply:
The slight gap you see is normal. The drum is not supposed to make contact with the brake mounting plate. There are some instances when mixing brands of brakes, hubs, and axles, that won't line up properly but in this case it is normal. I did also run it by another set of eyes just to make sure and we both came to the same conclusion.
Product Page this Question was Asked From
Brake Mounting Flange for 3" Round Axle
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Brake Mounting Flange
- 12 Inch
- 3 Inch Diameter Axle
- Redline
more information >
Continue Researching
- Shop: 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles - 26" Long
- Shop: Karrier ST205/75R15 Radial Trailer Tire w 15" Wheel with +.5 Offset - 5 on 4-1/2 - Load Range C
- Shop: 6-Leaf Double-Eye Spring for 6,000-lb Trailer Axles - 26" Long
- Shop: Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long
- Shop: Lippert Manual Pull-Out Step for RVs - Single - 6" Drop - 24-1/4" Wide - Steel - 300 lbs
- Shop: 4,500-Watt Portable RV Generator - 3,600 Running Watts - Propane or Gas - Electric Start
- Video: Kenda Tires and Wheels - Tire with Wheel - AM32352 Review
- Video: Fantastic Vent RV Vents and Fans - Roof Vent - FV802250 Review
- Video: Review of Lippert Spare Tire Carrier - Under Chassis Mount - LC159056
- Video: Yakima EasyRider Utility Trailer SpareTire Carrier Kit Manufacturer Product Tour
- Video: Buyers Products Spare Tire Carrier - Truck Mount - 3375201010 Review
- Article: How to Accurately Measure Trailer Leaf Springs
- Video: Review of etrailer Trailer Leaf Spring Suspension - 4 Leaf Double Eye Spring 4000 lbs Axle - e22YR
- Video: Progressive Dynamics RV Power Control Center Installation - 2017 Airstream Flying Cloud Travel Trail
- Shop: Americana Baby Moon Trailer Wheel Center Cap - Chrome-Plated Steel - Qty 1
- Article: How to Raise Your Travel Trailer Height
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Q&A: Where to Mount the Brake Mounting Flange 4-44-1
- Q&A: Dimensions for a Brake Mounting Flange for a 3 Round Axle
- Q&A: Will 5 Hole Brake Backing Plate fit Mobile Home Axle
- Q&A: Recommended Brake Mounting Flange To Welded On Brake Assemblies
- Q&A: Replacement 12" x 2" Brakes For Trailer With Mobile Home Axles
- Search Results: brake mounting flange
- Q&A: Which Brake Mounting Flange for 3 inch Diameter Axle Beam
- Search Results: brake backing plate
- Search Results: conversion hubs for mobile home axles
- Q&A: Dimension Of Brake Mounting Flange For 7 Inch Electric Or Hydraulic Brakes
- Search Results: camper jacks
- Search Results: slide out jack
- Search Results: trailer jack