Installing the Redarc Tow-Pro Elite # RED44FR in a 2001 Ford Ranger

Question

Question:

I have a 2001 ford ranger I want to install a brake controller in. I like the Redarc controller but struggling finding a place to mount the remote. Do you have a video or pictures that pertain to my vehicle?

asked by: Earl

0

Expert Reply:

The Redarc Tow-Pro Elite # RED44FR is a great brake controller, but since it is still fairly new to use we haven't had the opportunity to shoot an install video on a Ford Ranger yet. I do have some dimensions that you can use to determine if it will fit though.

The main unit of the Elite measures 3-3/8" long x 3-15/16" wide x 1-1/8" tall while the control knob itself measures 2-3/8" long x 3/4" wide x 7/8" tall. If you are talking about having trouble finding a place to mount the control knob then I recommend using the Universal Mounting Panel # 331-TPSI-001 which allows a clean look for wherever you decide to install it.

If you check out the attached video of this controller being installed on a 2014 Jeep Grand Cherokee you can see that the control knob is actually mounted in the center console. Since the control knob doesn't have to be mounted in a specific orientation it really opens up the possibilities for installation.

Please note that if you already have a 4-Way like part # 118344 then you will also need the Universal Wiring Kit # ETBC7 for a fully functioning 7-Way. I have attached a video of this kit being installed on a 2001 Ranger for you to reference as well as some helpful articles.

expert reply by: Jon G

0

click to enlarge

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Installing the Redarc Tow-Pro Elite # RED44FR in a 2001 Ford Ranger

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching