Replacement Reese 5th Wheel Hitch Head Mounting Bolts

Question

Question:

I need the large pin measures 1 1/2inch x 4 to 5inch that connects the two pieces of the 30038 slider to the assembly which holds the jaws. Please help

asked by: Jim

0

Expert Reply:

I believe you are looking for the Replacement Hardware for Reese 16K Fifth Wheel Head Assembly and Head Support # 30583. These bolts mount the head cross assembly to the legs and are only available in the kit.

expert reply by: Jason S

0

Answer 1

For the Reese/Pro Series 15k fifth wheel hitch you have the way to order replacement pins for the head of the hitch is with the part #30583 which does come with additional hardware but it's only way to get just the pins.

view full answer...

Answer 2

Yes, I went out to our warehouse and checked the Replacement Hardware for Reese 16K Fifth Wheel Head Assembly and Head Support part #30583. It does indeed come with four 1/2" hex head bolts and four 1/2" nyloc nuts which will be used to…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Replacement Reese 5th Wheel Hitch Head Mounting Bolts

Product Page this Question was Asked From

Continue Researching