Recommended Brake Controller and Wiring for 2017 Ford Expedition with 4-Way

Question

Question:

Vehicle: 2017 Ford Expedition 4x4 XLT Problem: Tow package with 4 pole and no trailer brake controller. I need a TBC, 7 pole, and anything else that I may need to make it all work. I am looking to make a single purchase to ensure I can tow a trailer properly and all parts fit to each other during one install. - Trailer Brake Controller that will fit in the slot the factory would have use to put one but did not for some reason. - TBC adapter if required. - 4 to 7 pole adapter - Would like a 4 to 7 pole adapter to use both such as Item # C57674. Could eTrailer assist in this matter and help provide some options that would best fit with out breaking the bank? Thank you.

asked by: Brandon

0

Expert Reply:

We have everything you need to install a fully functional 7-Way connector and a trailer brake controller on your 2017 Ford Expedition.

Since your Expedition is already equipped with a 4-Way connector, you will just need the Universal Wiring Kit # ETBC7. This kit includes everything needed to install a 7-Way connector from your existing 4-Way, along with the needed wiring and circuit breakers for installing a brake controller. The connector that is included features both a 7-Way and 4-Way like what you are wanting.

I have attached a great article that details the installation steps for this kit that you might find helpful.

Then, for the brake controller, I highly recommend the Tekonsha Prodigy P2 # 90885. This is an excellent, proportional controller that will activate the trailer brakes at the same time and with the same intensity that you apply to them in your Expedition. I am not sure of the dimensions on the factory brake controller slot that you referenced, but this unit measures 3-1/8 inches wide, 5-1/8 inches long, and 2 inches tall. You can compare that to the opening in your vehicle to see if this will fit. Otherwise, a pocket mount is included that you can install under the dash.

To install the controller, you can use the Plug-In Adapter # 22292. One end of the adapter will plug into the brake controller itself, while the other end will connect to the built-in port beneath the vehicle's dash.

I have attached a couple short video demonstrations, along with the installation instructions for the products mentioned that you can check out.

expert reply by: Chris R

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 11

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 12

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Recommended Brake Controller and Wiring for 2017 Ford Expedition with 4-Way

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching