Comparing Curt 2 Inch Trailer Hitch Receiver to Draw-Tite 2 Inch Receiver for 2018 VW Atlas
Question:
Thanks! But I still can’t compare the two hitches directly - in the X direction per my picture. On the Draw Tite you reference backward from the mounting hole, and on a the Curt you reference forward from the bumper. Can you make them from the same reference point? Thanks for the drop comparison- those are from same reference.
asked by: Steve
Expert Reply:
For your 2018 VW Atlas, the Curt Trailer Hitch Receiver # C13366 will be about 1-1/2 inches recessed behind your bumper and will drop 8.44 inches from the mount to the bottom of the receiver tube according to my tech contact at Curt.
The Draw-Tite # 76176 will have the receiver tube extend about 6-1/2 inches from the rear mounting hole and will drop 8.8 inches from the mount to the bottom of the receiver tube according to my tech contract at Draw-Tite.
For your trailer wiring, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118754 confirmed to fit your vehicle and then the B&W Tow & Stow 3-Ball Mount # BWTS10048B and locking pin # e98882.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 900 lbs TW
- 6000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 900 lbs WD TW
- Completely Hidden
- Draw-Tite
more information >
B&W Tow & Stow 3-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- 2-5/16 Inch Ball
- Three Balls
- Steel Ball
- Steel Shank - Matte Black
- Drop - 5 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- B and W
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Stainless Steel
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 900 lbs TW
- 6000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Trailer Hitch Fit for 2021 Honda CR-V Hybrid
- Q&A: Most Hidden and Best Ground Clearance Hitch for 2019 Volkswagen Atlas
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Q&A: 2018 Volkswagen Atlas Trailer Hitch Receiver Recommendation for a Bike Rack
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Trailer Hitch Recommendation for 2018 Volkswagen Atlas
- Q&A: How to Install a Brake Controller on a 2001 Toyota Tundra SR5 With Factory Tow Package
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Do You Recommend the Saris Freedom 4 or the Hollywood Racks Destination 4 for My 2018 Atlas?
- Q&A: Trailer Hitch for 2018 Volkswagen Atlas SE for Bike Towing Use
- Article: Best Hitches for Travel Trailers (2022) - For a Smooth, Sway-Free Ride
- Article: Trailer Hitch Installation Tips
Steve
4/3/2018
Thanks! But I still can’t compare the two hitches directly - in the X direction per my picture. On the Draw Tite you reference backward from the mounting hole, and on a the Curt you reference forward from the bumper. Can you make them from the same reference point? Thanks for the drop comparison- those are from same reference.