Backup Sensors Interference With BumpStep Hitch-Mounted Bumper Protector and Step?

Question

Question:

Will this item have any interference with the sensors Toyota RAV4 2018

asked by: Joey H

0

Expert Reply:

I reached out to my contact at WeatherTech regarding backup sensor interference with the BumpStep Hitch-Mounted Bumper Protector and Step for 2" Hitches # WT81BS1, and he advised me of no known issues with this matter.

expert reply by: Timothy G

0

Answer 1

We carry the WeatherTech BumpStep Hitch-Mounted Bumper Protector and Step for 2" Hitches #WT81BS1 and recently added the BumpStep XL #WT81BS1XL which has a 24 inch length versus the 12 inch length.

view full answer...

Answer 2

I went out to the warehouse and pulled the Hopkins 4, 5, and 6-Way mounting bracket #HM48605 to measure it for you. The outer most holes are 2-7/8 inches apart on center. The inner set are 1-7/8 inches apart on center. The holes are just a hair…

view full answer...

Answer 3

I recommend the Hopkins Mounting Bracket #HM48605 for securing the Pollak 5-Pole, Round Pin Trailer Wiring Socket #PK11502. The Hopkins bracket has a slit in the bottom which allows you to easily attach and remove the connector without having to…

view full answer...

Answer 4

That is a great question, but I can assure you that the EcoHitch Hidden Trailer Hitch Receiver #306-X7601 will have no affect whatsoever on the rear backup sensors on your 2019 Subaru Outback Wagon, both during installation and when the hitch is…

view full answer...

Answer 5

Thank you for the picture. Unfortunately, there isn't going to be a hitch for the 2017 Ram ProMaster 3500 that is compatible with that step. Even something like the Draw-Tite #75882 which hangs down a little bit further than the Curt #C13295 is…

view full answer...

Answer 6

I wouldn't think so, but to be sure you can compare the measurements of the Weathertech part #WT81BS1 to the backup sensor locations. This is overall 11-1/2 inches wide and 2-1/2 inches tall. This should be small enough and also low enough not to…

view full answer...

Answer 7

Since you are looking for a step that can be used with your tailgate down, I recommend taking a look at the HitchMate Extendable TruckStep, #HE4045. This step was designed for that specific purpose and offers a support strut that extends step…

view full answer...

Answer 8

For the lift gate kick sensor with your 2021 Honda Pilot and the Curt Trailer Hitch Receiver #C13146, I have also read that some have not had to relocate the sensor with the Honda kit. But some have also expressed that the system works but not all of…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Backup Sensors Interference With BumpStep Hitch-Mounted Bumper Protector and Step?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching