Does Hopkins 4-Flat Connector # HM43415 Have a Tail Light Converter?

Question

Question:

does it have a tail light converter? 1997 toyota 4runner

asked by: Lupe F

0

Expert Reply:

Yes, the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # HM43415 does have a tail light converter so your 1997 Toyota 4Runner's wiring will match that of your trailer. I do recommend using dielectric grease # 11755 on the electrical connections in order to help prevent corrosion.

expert reply by: Kyle S

0

Answer 1

The Hopkins Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, Item #HM43415, simply plugs into the existing wiring of your 1996 Toyota 4Runner. It will plug into your 4Runner's wiring harness that is located in the rear cargo area…

view full answer...

Answer 2

I know exactly what you need; I recommend using the Timbren Rear Suspension Enhancement System #TTORSEQ. The Timbren SES is designed to combat the sag you're experiencing and provide a more comfortable ride by absorbing road shock and improving…

view full answer...

Answer 3

I would not recommend using passenger vehicle tires on your tandem axle boat trailer. You will only want to use trailer tires that have the letters ST in the size. ST stands for Special Trailer tire, which is meant to be used on boat and utility…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Does Hopkins 4-Flat Connector # HM43415 Have a Tail Light Converter?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching