Available Lippert RV 2-Step Units for Trailers and Motorhomes

Question

Question:

At the Chicago RV show I saw thee Lippert Solid Step. Do you carry the two step model?

asked by: Kent H

0

Expert Reply:

We offer the two step versions of the Lippert SolidStep RV step unit. Currently we have the # LC733931, # LC713662, and # LC733932. You will want to measure your door frame to determine the best fit for your RV.

expert reply by: Adam R

0

Answer 1

The widest point of the Lippert #LC733932 Solid Step is 24 inches, which is the dimension from the outside of one stringer to the outside of the other. The latching mechanism that holds the steps folded upright into their storage position is width…

view full answer...

Answer 2

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 3

While we do not carry that particular Lippert step we do have the similar MORryde #MR98RR or a better option in my opinion is the TorkLift GlowStep #TLA9104. I prefer this step as it folds up nicely and works better in tight areas like storage lots.…

view full answer...

Answer 4

I spoke with MORryde since the STP-017 is an OEM number and everything we offer is aftermarket and was found that that number should relate to the MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways #MR26RR. I would just measure…

view full answer...

Answer 5

The SolidStep Manual Fold-Down Steps part #LC791572 will fit a door way from 25" -28.9" wide when measuring the frame inside. If the factory label sticker shows a doorway width between 26"-29" then the above steps will work for…

view full answer...

Answer 6

In terms of choosing a Lippert Solid Step, you'll use the width of the finished door at it's narrowest. Round that number up to the next full inch, which in your case would be 28 inches. In that case, you'll want the adjustable model…

view full answer...

Answer 7

Yes, the #TLD2142 is exactly what you need for your 2019 Ram 3500 with running boards extending under the truck bed. For the rear, you need the #TLD3112 if you have the factory hitch or #TLR3510 if you have the TorkLift SuperHitch Magnum 30K.

view full answer...

Answer 8

We've seen this issue before on an older camper that had the screen door installed a little lower than how they are now. An installer here actually had this exact problem. If your door is close to closing, a couple suggestions that you can try…

view full answer...

Answer 9

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 10

I have found with a lot of the older campers like your 1995 Prowler that the screen doors are installed lower so it creates an issue when closing. Unfortunately there aren't a set of steps like the SolidStep Manual Fold-Down Steps that…

view full answer...

Answer 11

The MORryde StepAbove RV Steps #MR85RR weighs about 70 lbs. As far as the flip step, I assume you are referring to the MORryde Flip Tread RV Steps #MR42UR which weighs about 45 lbs. Both of these steps will fit your 28" wide door. Personally I…

view full answer...

Available Lippert RV 2-Step Units for Trailers and Motorhomes

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching