Why Would Proportional Brake Controller Activate Trailer Brakes in Reverse

Question

Question:

We have just bought a caravan and are having trouble with the setting of the braking system to reverse. The caravan tows beautifully moving forward, but I cannot find how to adjust the setting so the vehicle is able to reverse. When we try the caravan just feels like it locks up. There is no light that shows on the controller when the gears are put into reverse. Should there be a light? Thanks

asked by: Debbie G

0

Expert Reply:

Is the controller applying voltage on the display when you are in reverse? If so that means the red wire (brake light circuit) is seeing voltage all the time and the controller thinks you are stopping. You need to verify that the red wire is attached to a circuit that only sees voltage when the brakes are applied.

I attached a help article with more info on brake controller troubleshooting for you to check out as well.

expert reply by: Jameson C

0

Answer 1

It sounds like the weld nut that holds the rear bump stop on your 2006 Ford F-150 has broken. Basically, there is a nut that is welded to the inside of the frame rail and is used to secure the bump stock via the center bolt. The tack welds that hold…

view full answer...

Answer 2

It sounds like your wires are connected wrong. You most likely have your 12V power connected to your reverse light function which is why it is getting proper power in reverse, but is losing power when you shift to drive. I recommend using a circuit…

view full answer...

Answer 3

Are you certain that you have the 6-way connector, like part #PK12720 with the 6 round pins? Or do you have the 7-way connector like part #PK11893 that features 6 blade-type pins with one connector in the center? The two can sometimes be confused.…

view full answer...

Answer 4

In this senario, I would run a wire from the center pin of the 7-way to the reverse light circuit on your truck. This will enable you to bypass the fuse. Because of this direct connection you should be able to back up without your trailer brakes…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Why Would Proportional Brake Controller Activate Trailer Brakes in Reverse

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching