Are there Stainless Steel Wheel Studs for Trailers

Question

Question:

Do you carry stainless steel wheel studs? Is there even such an animal? Please advise. Thanks.

asked by: Keith M

0

Expert Reply:

There probably are some stainless steel wheel studs out there somewhere but all the ones we have are either zinc-coated steel or painted steel. If you are having a corrosion problem you might want to consider some thread sealant # LT37482. It will help prevent the treated threads from corroding.

expert reply by: Michael H

0

Answer 1

We have just what you are looking for. I called my contact at TDE and asked about the hub you have on your boat trailer. They told me that it was a 5-stud idler hub for a 3,500-lb axle. That means you need the part #AKIHUB-545-35-K. This is a fit for…

view full answer...

Answer 2

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Are there Stainless Steel Wheel Studs for Trailers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching