Differences Between the Two Camco RV Power Defender Units

Question

Question:

What is the difference between this defender and the more expensive one?

asked by: Pat

0

Expert Reply:

The difference between the Camco RV Power Defender 30 amp, part # CAM55312 and the Camco RV Power Defender 50 amp, part # CAM55313 is the amperage that they work on.

The 50 amp variant is built for higher power drawing RVs, while the 30 amp is designed for lower power RV's. You'll want to match your particular plugs and required amperage to your RV when choosing which product to buy.

expert reply by: Jacob W

0

Answer 1

The Camco RV Power Defender Circuit Analyzer part #CAM55313 and Camco RV Power Defender Voltage Protector part #CAM55306 are similar in that they both work to protect the trailer from power surges and have diagnostic lights to help with…

view full answer...

Answer 2

The Camco RV Power Defender Voltage Protector #CAM55301 that you referenced automatically disconnects when it senses that the voltage levels are at a dangerous point. Since it automatically reconnects when the voltage levels stabilize (between 102V -…

view full answer...

Answer 3

50-amp service and 30-amp service use different connectors. The 50-amp surge protector #CAM55313 uses 4-prong connectors while the 30-amp surge protector #CAM55301 uses 3-prong connectors. So you will need to have one for each type of campground…

view full answer...

Answer 4

The Camco RV Power Defender, part #CAM55312 can only withstand a single surge. It cannot reset its surge protector once its used, and will need to be replaced.

view full answer...

Answer 5

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Differences Between the Two Camco RV Power Defender Units

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching