Anti-Rattle Device/Hitch Lock Recommendation for 2016 Toyota Tacoma

Question

Question:

What hitch pin locking preferred will fir my 2016 Tacoma w OEM 5howing package? Prefer a little slop as possible.. Thanks

asked by: Dan B

0

Expert Reply:

For a hitch lock with a built in anti-rattle device the part # 63232 is a great option for your 2016 Toyota Tacoma.

This holds the hitch accessory tightly to the side wall of the hitch tube and has a lock to prevent anyone from removing the hitch accessory unless they have the key.

I attached a review video for this for you to check out as well.

expert reply by: Jameson C

0

Answer 1

No, you don't have to use the sleeve when you install the Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches #63232. The main point of that sleeve is to keep the spring in good shape in the packaging and to my understanding you won't…

view full answer...

Answer 2

The usable length of the anti-rattle hitch lock part #63232 that you referenced is 2-5/8 inches which would be the correct length to fit the 2 inch hitch you have.

view full answer...

Answer 3

Yes. Lets Go Aero redesigned the Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches - 3-1/2" Span #63232 you were looking at a few years back to prevent the issue of the bolt freezing in the block. I do however recommend removing the…

view full answer...

Answer 4

Our most popular anti-rattle device we offer is the Lets Go Aero hitch lock part #63232 that fits a 2 inch hitch like what you have. This would work well with the hitch of your 2018 Toyota 4Runner. I attached a review video for this for you to check…

view full answer...

Answer 5

I have a solution for you, but based on the picture you submitted of the hitch you have on your 2012 Toyota 4Runner (thank you for that by the way), the part #RM-061 would not work well for you. Instead I would recommend the part #63232 as this is an…

view full answer...

Answer 6

For your 1998 Toyota 4Runner, the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13087 is a confirmed fit that will not require any drilling. To use this hitch to tow a small trailer, I recommend the Tekonsha T-One Vehicle Wiring…

view full answer...

Answer 7

Since hitch locks like the #63232 don't end up carrying the full weight of a trailer they don't normally have towing capacities so it will work well for you. As long as you are using this hitch lock in the correct size hitch it's going to…

view full answer...

Answer 8

We do not sell just the internal block of the anti-rattle device part #63232 that you referenced so your best option would be to get a second one of these for use with your trailer ball that way you wouldn't have to mess with setting up the…

view full answer...

Answer 9

Based on similar vehicles we've tested the tilt feature of the Inno bike rack part #INH120 on it would allow the rear hatch of your 2023 Acura RDX to open the rear hatch with the rack tilted back. It would definitely be stable enough for a long…

view full answer...

Answer 10

We have many bike racks that will work with a Curt trailer hitch, like part #C11085, on your 2010 Honda Accord LX, however, the Hollywood Racks Road Runner 3 Bike Rack, #HR310, will not fit. The fit issue is not with the bumper of your vehicle, but…

view full answer...

Answer 11

It looks like on your 2011 Kia Soul, you will have to place the Curt Support Strap, #18050, in the gap between the body of the vehicle and the top of the rear hatch. You may have to open the rear hatch to get the hook in place and then close the…

view full answer...

Answer 12

Normally we recommend that the Curt Stabilizer Strap #18050 get hooked to the top of the trunk lid or top of the hatch, since your vehicle has a small spoiler this can be prove to be a difficult situation. If the spoiler has metal support underneath…

view full answer...

Anti-Rattle Device/Hitch Lock Recommendation for 2016 Toyota Tacoma

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching