What Material is the B&W Tow & Stow 3-Ball Mount # BWTS10048C Made Out of

Question

Question:

what is BWTS10048C made out of

asked by: Chuck

0

Expert Reply:

The B&W Tow & Stow 3-Ball Mount # BWTS10048C that you referenced is a steel construction for strength, but it also has a dual-process chrome plating on the shank and hitch balls for excellent rust resistance.

The pins included with the ball mount are stainless steel which makes them sturdy and rustproof.

I have attached a review video for you to check out as well.

expert reply by: Jon G

0

Answer 1

The B&W Tow & Stow 3-Ball Mount #BWTS10048B do not come with a keyed locking pin to secure the shank to the receiver. For that I recommend the Master Lock Trailer Hitch Receiver Lock for 2" Trailer Hitches #1480DAT. If you want a locking…

view full answer...

Answer 2

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 3

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 4

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 5

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 6

Currently the InfiniteRule Trailer Coupler Lock #IR58FR is only offered keyed unique. For a keyed alike option you will want to refer to one of our etrailer Locks #e98886 or #e98889 and select keyed alike from the drop down box when placing your…

view full answer...

Answer 7

The B&W Silencer Pad #BWTS35020 is intended to be placed on the shank of one of their Tow & Stow Multi-Ball Mounts like #BWTS10048B so that it acts like a gasket between the collar on the end of the hitch's receiver tube and the…

view full answer...

Answer 8

The distance between the 1/4" pin and the main lock body on the #IR98FR is 11/16". The length of the sides is 2-1/16".I have attached a diagram below showing all of the measurements for your reference.

view full answer...

Answer 9

Since heat rises I would at the very least put a set of the Trailer Vents #HMAV2-AVT2 near the top of the trailer to get the hottest air of the trailer out. What you could do for maximum air flow in your trailer is have a set facing forward in the…

view full answer...

Answer 10

The information I have on a 2000 Toyota 4Runner is that a brake controller has to be hardwired in so you would follow the instructions in the FAQ I have linked. The black wire on #C57102 will connect to the positive battery terminal via a 40 amp…

view full answer...

Answer 11

After you plug the 4-way in from your 2006 Ford E-350 to the Curt Trailer Connector Adapter #C57102 you will need to run the rest of the wires as follows: The white wire will need to be grounded to a clean metal surface. The blue wire will go to the…

view full answer...

Answer 12

So the first thing you should note is that if you don't need a reverse light circuit or an accessory circuit you don't have to complete those wires. You can leave those off for most situations. Normally the 12 volt power wire runs to the…

view full answer...

What Material is the B&W Tow & Stow 3-Ball Mount # BWTS10048C Made Out of

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching