Installing a Curt Class 1 Hitch for 2008 Acura TL

Question

Question:

Hi. I am interested in purchasing a Curt trailer hitch for my 2008 Acura TL to install a Thule bike rack. I think it is better than that of Draw Tite since it is directly attached to the bumper as opposed to trunk pan. Thought that would be more rigid and also probably cause less structural damage if involved in rear hit accident. But would like to know whether the installation will require any trimming/shaving of stock bumper cover or any other body adjustments other than drilling of bumper. Any input on upside/downside between the brands is appreciated. Thanks.

asked by: Jonas

0

Expert Reply:

Outside of drilling into the bumper, there are no other modifications required to install the Curt Class I hitch, part # 11321 onto your 2008 Acura TL.

I've included our trailer hitch installation guide to help make your installation process as easy as possible.

expert reply by: Jacob W

0

Answer 1

To carry bikes on your 2004 Acura TL, I'd recommend going with the Draw-Tite #24755 hitch over the Curt #11321 model. Curt's warranty stipulates that an extra stabilizing strap #18050 be used with non-trailer loads on their Class I hitches,…

view full answer...

Answer 2

It sounds like you are looking for a trailer hitch and related towing parts to pull a trailer with your 2004 Acura TL. We do offer light-duty Class I hitches for your car and all can be seen on the linked page. The one I suggest for the best…

view full answer...

Answer 3

Although they have the same weight capacity, I'd rather see you use the Curt Class I hitch, part #11321. Rather than bolting to the underside of the trunk pan like the Draw-Tite, the Curt hitch bolts to the underside of the rear bumper beam which…

view full answer...

Answer 4

Installation of the Curt Trailer Hitch, part #11321, does require drilling on your 2005 Acura TL. The hitch will attach to the bumper beam, so it does not require trunk access. The Curt Trailer Hitch #11321, includes a drawbar, pin and clip. To…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Installing a Curt Class 1 Hitch for 2008 Acura TL

Featured Help Information

Miscellaneous Media

Continue Researching