Will Thule Bike Rack Fit in Curt Trailer Hitch Receiver 13424

Question

Question:

Will this hitch fit a Thule bike carrier in it?

asked by: Bryan

0

Expert Reply:

Yes, basically any Thule bike rack out there that is designed to fit a 2 inch hitch will fit well in the Curt hitch part # 13424.

expert reply by: Jameson C

0

Answer 1

Yes, the carriage bolt blocks (they do look like spacers) and all install hardware are included with the Curt hitch part #13424. I attached a picture that shows all of the hardware that comes with the hitch. CM-SP6 is called out in the instructions…

view full answer...

Answer 2

Yes, the Curt hitch #13424 that you referenced does fit a 2010 GMC Acadia. I attached an install video for this hitch on a 2010 GMC Acadia like yours for you to check out as well.

view full answer...

Answer 3

The Curt #13424 and etrailer.com #e98863 trailer hitches use M12-1.75 x 30mm bolts for the installation while the Draw-Tite #75528 trailer hitch uses M12-1.75 x 45mm bolts for the installation on a 2012 Chevy Traverse. I have linked the…

view full answer...

Answer 4

The Thule EasyFold XT part #TH03202 would be a great rack to use with your Aventon e-bikes but to use it without an adapter bar would require your frame to be less than 3-1/8 inches thick. Yours looks pretty thick so I would recommend measuring. If…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Will Thule Bike Rack Fit in Curt Trailer Hitch Receiver 13424

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching