Trailer Hub Seal Recommendation for Hub with Bearings 15123 and 25580

Question

Question:

i have bearings 15123 and 25580 but i have a seal with the number 10-54. Do you have a kit with this seal?

asked by: John K

0

Expert Reply:

For that bearing combo the recommended seal is the part # RG06-070 which has an inner diameter of 2.25 inch and and outer diameter of 3.376 inch. If yours has a different measurement let me know and I'll see what we have that would fit.

expert reply by: Jameson C

0

Answer 1

Each of the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3.5K #23-468-469 you were looking at include a left and right side braking assembly. Since your 2012 Keystone Bullet Premier 31' has two…

view full answer...

Answer 2

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 5

The Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall #093026 you were looking at has a hole just to allow you to measure the height of the hanger, and the hole lines up with the bottom of the support that the hanger rests against. To…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs #DL24239 or…

view full answer...

Answer 9

The Dexter Grease Seal 010-036-00 is interchangeable with the Dexter Grease Seal 010-054-00 although they have a slightly different outer diameter, 3.371" (010-036-00) vs 3.376" (010-054-00) but they do both have the same inner diameter of…

view full answer...

Answer 10

Yes, you can use the seal part #RG06-070. I looked up the K71-386-00 seal that you mentioned and it has matching dimensions, an inner diameter of 2.25 inches and an outer diameter of 3.376 inches. This seal is commonly found on Dexter axles rated…

view full answer...

Answer 11

The Kodiak Disc Brake Kit - 12" Hub/Rotor - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs #K2HR526D fits axles with a #42 spindle. This uses #25580 inner and #15123 outer bearings which are the most common size bearings for a 6k axle like the…

view full answer...

Answer 12

To replace your Dexter 10-36 grease seals I recommend using Grease Seal #GS-2250DL. This seal has an inner diameter of 2.25" and outer diameter of 3.376". This is a double lip seal.

view full answer...

Trailer Hub Seal Recommendation for Hub with Bearings 15123 and 25580

Product Page this Question was Asked From

Continue Researching