How To Install a Brake Controller on a 1999 GMC Yukon
Question:
is there a place in the fuse block that u hook up a brake controller on a 99 yukon denali
asked by: Dallas R
Expert Reply:
When installing a brake controller such as the Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 on your 1999 GMC Yukon you will want to run the power wire (black) from the brake controller to the battery not the fuse box. You will also want to use a 20 amp circuit breaker like part # PK54220PL in between the controller and battery. Place the circuit breaker 6" from the battery and run the remaining wire to the brake controller.
You will also need both 4 and 7-way trailer connectors if you do not already have a 7-way trailer connector and for this I recommend using both the Curt T-Connector Vehicle Wiring Harness part # C55319 and the Universal Installation Kit for Trailer Brake Controller part # ETBC7. The universal brake controller installation kit will allow you to run the electric brake output signal from the trailer connector into the cab of your vehicle.
I have attached a brake controller installation video on a similar vehicle for you in addition to a wiring diagram.
Products Referenced in This Question
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Circuit Breaker - 20 Amp - Perpendicular Mount Bracket - Cycling Auto Reset - Plastic - Type I
- Accessories and Parts
- Wiring
- Circuit Breaker
- 20 Amp
- Pollak
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Search Results: 20142
- Search Results: 56468
- Search Results: 13493
- Shop: Towing Mirrors
- Shop: K-Source Custom Extendable Towing Mirror - Electric/Heat w LED Signal - Textured Black - Driver
- Shop: CIPA Custom Towing Mirror - Slip On - Driver Side
- Shop: K-Source Snap & Zap Custom Towing Mirrors - Snap On - Driver and Passenger Side
- Search Results: 25980ez
- Search Results: gnxa2061
- Search Results: 8550048
- Shop: Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Search Results: tekonsha 90160
- Shop: Trailer Connector Adapter w/ Lamp-Out Sensor Bypass - 7-Way RV to 7-Way RV - Vehicle End
- Shop: Roof Rack
- Shop: 4" Offset Ball for B&W Turnoverball Gooseneck Trailer Hitch for Toyota Tundra
- Shop: Trailer Wiring
- Shop: RV Camera
- Video: Fastway Zip Trailer Breakaway Switch Installation
- Q&A: Which Stud Goes Where on Circuit Breaker PK54220PL
- Q&A: Can Different Circuit Breakers be Used if They Mount Differently Than Current Ones
- Q&A: How to Hard Wire Prodigy P2 Trailer Brake Controller
- Q&A: How to Wire a Trailer Break Away System and Connect Auxillary Battery and Brake Wires
- Article: Trailer Wiring Diagrams
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Shop: Trailer Hitch
- Video: Choosing the Right Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Trailer Wiring