Replacement Fan Motor Assembly for Create A Breeze Fan

Question

Question:

Will this fit the Create a breeze fan motor? Manual lift no thermostat. Number on existing fan blade is 48444. 2012 Winnebago Via 25T

asked by: Tom

0

Expert Reply:

The Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans # FVK8017-00 will fit your Create A Breeze Fan. This will work as a direct replacement for your manual lift no thermostat vent fan.

expert reply by: Jason S

0

Answer 1

Thanks for the picture of your roof vent. From that I can tell that the motor part #FVK8017-00 that you referenced is the correct replacement.

view full answer...

Answer 2

The 8100TR model number was in a lot of the older Fan-tastic Create-A-Breeze vents. You can use Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans part #FVK8017-00 which is designed to replace the bow tie bracket, fan blades and…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 9

The Dexter 8-222 model hubs currently on your trailer are designed primarily for mobile home use, and these types of hubs typically use unique bearing combinations that make it really difficult to find full replacement assemblies. Mobile home parts…

view full answer...

Answer 10

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement Fan Motor Assembly for Create A Breeze Fan

Product Page this Question was Asked From

Continue Researching