Hitch Receiver Needed for a 2004 Honda Rincon 650cc ATV

Question

Question:

Need a rear hitch for my 2004 Honda Rincon 650cc Atv

asked by: Terry

0

Expert Reply:

To install a hitch receiver on your 2004 Honda Rincon 650cc ATV you can use the Curt ATV Ball Mount Adapter with Welded D-Ring # C45006 which installs by bolting on to the tongue of your ATV. This will give you a 2 inch receiver and a D-ring for any of your towing needs.

If you need a hitch ball as well you can by the adapter with either a 1-7/8" hitch ball # C45029 or a 2" hitch ball # C45038.

expert reply by: Jon G

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

The Reese Towpower 3-Way ATV Hitch #RP7065000 measures 2" at two of the holes and then 2-5/8" at the middle one. I've attached a photo for you to reference.

view full answer...

Answer 8

For your 2012 Ford E-350 Econoline Van you can use a step like the Carr Custom-Fit Side Step #CARR124031-1 which will be a 5" wide step. If you are wanting a step for the driver and passenger side you can get the Carr Custom-Fit Side Steps…

view full answer...

Answer 9

The Blue Ox has a life expectancy of 8-10 years, Blue Ox does recommend replacing it at this point. There are a few big differences between the Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar w/ LED Lights - RV Mount - 8K #RM-676 and the Blue…

view full answer...

Answer 10

On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…

view full answer...

Answer 11

The Replacement Lock Cylinder for BOLT Toolbox Latch part #BL7023481 was designed to work with most truck tool bax locks. Those locks are very similar to the lock on the ARE caos but there is no way to guarantee. Anothe option is the Pop & Lock…

view full answer...

Answer 12

The Timbren Axle-Less Trailer Suspension System #TASR7KS01 is the highest rated weight capacity we have a 7,000lbs. This would require the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-464-465 and 2 Dexter Trailer Hub and Drum Assemblies…

view full answer...

Hitch Receiver Needed for a 2004 Honda Rincon 650cc ATV

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching