Will Pro Series Trailer Jack # PSEA20000340 Replace a Shelby # 5793-24Z
Question:
Will this jack properly replace the Shelby #5793-24Z jack that came on my Herritage boat trailer?
asked by: Mike
Expert Reply:
According to the research I did, the Pro Series Round, A-Frame Jack, # PSEA20000340, is comparable to the Shelby jack you have referenced. There are some minor differences.
First, they both fit the standard A-frame mounting pattern and have a 2,000 pound capacity and have a top wind design.
The differences are in the dimensions. According to Shelby, their jack has 15 inches of travel, the Pro Series has 14 inches of travel. The extended length from the mounting bracket to the bottom of the Shelby jack is 24 inches. On the Pro Series it is 22 inches. Retracted height for the Shelby is 8-1/2 and the Pro Series is 8 inches. And last, on the Shelby, from the mounting bracket to the top of the jack measures 12 inches. For the Pro Series, that measurement is 11 inches.
So as you can see, the jacks are only off in term of dimensions by a few inches at the most. The Pro Series jack would make a good replacement for the Shelby.
Product Page this Question was Asked From
Pro Series Round, A-Frame Jack - Topwind - Zinc Plated - 14" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Topwind Jack
- 14 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Pro Series
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Bright Way Switch Mode Battery Charger for Hydraulic Lift and Dump Trailers - 12V - 5 Ah
- Shop: T-One Vehicle Wiring Harness with Upgraded Circuit Protected ModuLite HD Module - 4-Way Flat
- Search Results: 118781
- Search Results: 5214
- Shop: Replacement 14" x 7-1/2" Carbon Air Filter for Dometic Duo-Therm RV AC Unit - Qty 1
- Shop: Pro Series Round, A-Frame Jack - Topwind - Zinc Plated - 14" Lift - 2,000 lbs
- Video: B and W Four Inch Offset Gooseneck Hitch Ball Review
- Shop: 4" Offset Ball for B&W Turnoverball Gooseneck Trailer Hitches
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Shop: Gooseneck Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Is Footplate from Shelby 5793 Jack Compatible with Pro Series Round, A-Frame Jack # PSEA20000340
- Search Results: roof vents
- Search Results: 118480
- Search Results: 75902
- Search Results: awning lift handle
- Shop: Suspension Enhancement
- Shop: Exhaust
- Shop: Roof Rack
- Shop: Radiator Fan
- Article: Stability Control for Heavy Duty Vehicles
- Search Results: trailer jack
- Video: B&W Continuum Weight Distribution System Review
- Video: Pro Series Trailer Jack - A-Frame Jack - PSEA20000340 Review
- Q&A: Pro Series Round Replacement A-Frame Jack with 3 inch Standard Mounting Holes
- Q&A: What Brake Actuator Replaces The TDE Model LP8000 Class IV Actuator
- Video: Pro Series Round A-Frame Jack Review PSEA20000340
- Q&A: Required Bolt Length for Installing A-Frame Trailer Jack