What are Overall Dimensions of Typical Trailer Axle

Question

Question:

I am building my own axel and I need to know the distance between the spring perch and the hub. 3500# axel for a pull type smoker. Thank you

asked by: George W

0

Expert Reply:

There isn't a set dimension for that on trailers. Typically axles are custom ordered to the specs needed. They order the spring seat to seat dimension for mounting to the trailer and then the hub face to face dimension for what will clear the fender wells.

For example, we have the 3,500 lb trailer axle part # T3584F-EZ-8974 which has 89 inches from hub face to hub face and then 74 inches from spring seat to spring seat.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The big things we are looking for on the label are the weight capacity, hub face (HF) length, and the spring center (SC) distance. Your axle is a 4,400 lb 85" HF and 68-1/2" CS Dexter axle. I will tell you up front that we do not…

view full answer...

Answer 2

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...

Answer 3

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 4

The only 7K axles we offer with straight spindles are the Dexter #8327834 axle you'd looked at and the same axle with brake drums/hubs, part #8327834-EB. These axles have a hub face to hub face distance of 95 inches and a spring seat center to…

view full answer...

Answer 5

There isn't a specific distance the hangers have to be for hanger kit #AP216-H238. A good place to start is 30-1/2 inches on center but you would only really know by mocking it up on the trailer before permanently installing the hangers. To…

view full answer...

Answer 6

The equalizer in the Tandem-Axle Trailer Equalizer Kit #AP216 is 11-1/2" on center from the outer spring mounting holes when measuring horizontal separation. One hole will be 6" on center from the equalizer mounting hole center and the…

view full answer...

Answer 7

That does make sense. We don't have an exact replacement for your application but if you check out the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles #7685269 you can see that it has 95" hub-face and 80" spring-center…

view full answer...

Answer 8

Certainly; the correct leaf spring for your 2022 Grand Design 295RL is the 6-Leaf Double-Eye Spring #e94SR.

view full answer...

Answer 9

If you look at the backs of the brake assemblies there should be a hole where the magnet wires come out and a little opaque plastic strap. So if you are looking at the back of the assembly and those items are on the left then it is the left side…

view full answer...

Answer 10

In the attached diagram the A measurement is actually the distance from the center of the spring hangers for a single axle trailer. The spring eye to spring eye measurement for your leaf springs will be slightly different. The B measurement that you…

view full answer...

Answer 11

Spring Hanger location dimensions are normally figured by the manufacturer and provided with the spring hanger kit, that includes all of the parts for installing the springs on the trailer frame. I have provided a chart that shows the spring hanger…

view full answer...

Answer 12

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

What are Overall Dimensions of Typical Trailer Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching