How to Pick Out Correct Rise/Drop Ball Mount for 2016 Honda Odyssey

Question

Question:

I have your Draw Tight class three hitch on my 2016 honda odyssey. I am phrasing two jet skis and a triton trailer. Currently the bottom of my hitch socket is 10 inches from the ground and top is 12inches. Believe I need to have trailer about 18 -20 inches. Not sure on the math for how much lift I will need do I measure from the top of the hitch socket? Thanks for help. Also any good recommendation based on lift you recommend.

asked by: Todd M

0

Expert Reply:

When determining the amount of rise/drop ball mount you'd need the two dimensions you need are the distance from the top of the hitch opening to the ground and from the bottom of the trailer coupler when it's sitting level.

The difference between those two dimensions is the rise/drop you'd need.

So for sure we know the hitch measurement is 12 inches. Lets say your coupler height was 18 inches from the bottom of it that would mean you'd need a 6 inch rise like # C45090.

If your coupler height is different let me know and I'll get you set up!

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

I have exactly what you need to add a 7-way trailer connector to a 2016 Honda Odyssey. For this, you'll need to start with a 4-way trailer connector and I recommend the T-One Vehicle Wiring Harness part #118521 which is plug-n-play. Then you can…

view full answer...

Answer 3

The Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers #PD4645V is exactly what you need for your Magnetek 7300. We have checked with Progressive Dynamics before and this is what they told us is needed. The DC fuse board does not…

view full answer...

Answer 4

I looked at the owner's manual for your 2017 Ford Expedition to find the location of the fuses that are for towing a trailer. You might be best off checking your own manual to verify but here's what I found: In the power distribution box in…

view full answer...

Answer 5

I have a replacement jack option for you, but I do not recommend cutting off the footplate and drilling a hole in the tube to mount a caster like the Removable 6" Caster for 2-1/4" Trailer Jacks - Steel Caster - 1,200 lbs Item #JC-102 to…

view full answer...

Answer 6

For a Class III ball mount with 6-inches of rise use part #C45090 from Curt. We do not have one with the exact 5-1/4-inches you want but that small difference will not matter. You are correct that you want your trailer to be as level as possible to…

view full answer...

Answer 7

I did some checking online and found that Intech actually offers an off-road package for the Chase Flyer that uses the Timbren Axle Less kit, so while we haven't had the chance to do it we know it is possible. We also know these can be used on…

view full answer...

Answer 8

You do have a very interesting situation. When it comes to aluminum trailers we always defer to the manufacturer whether it is just a utility trailer or an RV trailer like your toy hauler. Aluminum frames can't always withstand the pressure of a…

view full answer...

Answer 9

Yes, you can install a fifth wheel hitch on a 2021 GMC Sierra 2500 with Carbon Pro Bed. For this, I recommend the Demco Hijacker Autoslide 5th Wheel Trailer Hitch part #DM8550034 with Demco Hijacker Premier Series Above-Bed Base Rails and Custom…

view full answer...

Answer 10

There is some trimming of the fascia required when installing on your 2020 Honda Odyssey when you are installing the Curt Trailer Hitch Receiver #C64NR. The only trimming required is a 1.75" x4" section of the bottom appearance panel, which…

view full answer...

Answer 11

We carry three 2 inch trailer hitches that fit the 2020 Honda Odyssey: Curt #C64NR, a Curt #C13370, and one from us #E98855. All of them are basically the same design except for the Curt #C64NR. When we installed it on a 2018 Odyssey it was an inch…

view full answer...

Answer 12

The parts needed and steps taken to install a brake controller, like the Tekonsha Prodigy P3 #90195, on your 2016 Honda Odyssey will really depend on what they are wiring for your 7-Way. If they have wired all of the functions then you will simply…

view full answer...

How to Pick Out Correct Rise/Drop Ball Mount for 2016 Honda Odyssey

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching