Where Does 12 Volt Accessory Wire Run to on Trailer Wiring

Question

Question:

Where does the black wire connect to on the trailer? curt 7way replacement wiring

asked by: Walt H

0

Expert Reply:

Sounds like you are talking about the 12 volt accessory circuit of a 7-way and are asking about where it would need to get ran.

Normally this circuit goes to the positive post of a trailer battery and is used to keep the battery topped off but it can also be ran to power exterior or interior trailer lights.

expert reply by: Jameson C

0

Answer 1

On some vehicles GM didn't complete a connection under the hood that is used to deliver power to the brake controller. On the front of the power distribution box on the inside of the driver's side fender, there are two studs that…

view full answer...

Answer 2

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque,…

view full answer...

Answer 3

The exterior lights on your trailer - stop, turn and tail - and the interior lights will usually be fed by different power sources. On an RV-style 7-way the stop/turn light signals are carried on the pins at the 3-o-clock and 9-o-clock positions and…

view full answer...

Answer 4

Yes, the iRV Wall-Mounted Multimedia Receiver #IRV64FR will have similar connections to your Jensen stereo and will make a good replacement. I linked a wiring diagram for you that shows the various input/output connections including the wire colors…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Where Does 12 Volt Accessory Wire Run to on Trailer Wiring

Product Page this Question was Asked From

Continue Researching