Mounting Single Axle Fenders With Trailer Fender Mounting Brackets

Question

Question:

How does the 8542 fenders mount with the brackets sold?

asked by: Chris C

0

Expert Reply:

The Fulton Single Axle Trailer Fender with Top Step - White Plastic - 12" Wheels - Qty 1 # F008542 mounts using brackets like the Mounting Brackets for Trailer Fender - 8"/12" Wheels - Galvanized Steel - Qty 2 # CE26061G-2. I've attached a video of a similar installation to show you how this fender can be installed.

expert reply by: Jason S

0

Answer 1

The CE Smith Single Axle Trailer Fender part #CE17100ATB that you referenced has a radiused lip on both sides of the fender. It can still be bolted on though as the fender lip does go flat. It will set flush to the side of your trailer, but the round…

view full answer...

Answer 2

You can definitely install the galvanized steel e-track on your trailer that has a galvanized steel floor, as really the only potential issues are when installing e-track on dissimilar metals. So you can absolutely install any of the following…

view full answer...

Answer 3

First, I would prime and paint the whole bracket if for nothing else but to make sure it is all uniform. Galvanized steel is going to require certain products to be able to paint it and have the paint last. the first thing you will need to do is…

view full answer...

Answer 4

A galvanized steel fender like #CE17701G has a corrosion-resistant zinc coating applied to it, while a raw steel fender like #CE17720 does not. Both types can be painted, but it will be easier to paint the non-galvanized part. In either case the…

view full answer...

Answer 5

Yes you need to use brackets like part #CE26065PGA or #CE26061G to install the Fulton Single Axle Trailer Fender with Top Step #F008542. Basically you just secure one side of the bracket to your trailer and then the other side of the bracket to the…

view full answer...

Answer 6

The Fulton Plastic Fender with Top Step, part #F008553, does not come with mounting hardware. Fulton does not provide mounting bracket kits for the fenders. You can use your fenders original mounting brackets or use the Redline Galvanized Steel,…

view full answer...

Answer 7

You actually should shoot for 4-1/2" of clearance between the top of your tire and the bottom of the fender well. This accounts for flex in your suspension. Unless 2,280 lbs is the GVWR (gross vehicle weight rating) of your trailer then you need…

view full answer...

Answer 8

The closest plastic fender to your current fenders that we carry is the Fulton Plastic Fender, #F008542, that you referenced. This fender measures 7-1/2 inches wide at the base and 6-3/8 inches wide at the top. It is 23-11/16 inches long and 8-11/16…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Mounting Single Axle Fenders With Trailer Fender Mounting Brackets

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching