How to Order a Quantity of 4 Camper Jacks

Question

Question:

Hello Im buying a 1500lb Skamper truck camper that needs 4 jack stands. Its old and I dont want to spend a ton of money on stands. I need 4 an notice all the sets are pairs, any in 4? Four 1000lb jacks will easily lift my camper correct? Thanks

asked by: Bill

0

Expert Reply:

The best priced pair of camper jacks we offer is the part # CJ31. If you needed a total of 4 of these jacks you'd need to order a quantity of 2 of these.

expert reply by: Jameson C

0

Answer 1

We've got what you're looking for. The Curt Front Mount Hitch Receiver, part #C31028 mounts to the undersides of the frame members at the front of your Jeep so that the receiver opening is located under the front bumper, as you can…

view full answer...

Answer 2

There is not an extension to the 57" Max Lift Height, Brophy Cable Camper Jacks #CJ31 but there is a taller option. I recommend the 67" version of the Brophy Heavy Duty Cable Camper Jacks, #CX74.

view full answer...

Answer 3

We do have a half kit (or single jack) of the Brophy Cable Camper Jacks - 57" Max Lift Height - 1,000 lbs #CJ31 you referenced. This is found as part #BR29ZR on our site.

view full answer...

Answer 4

The Brophy Cable Camper Jacks #CJ31 referenced in your question are designed to allow for easy loading and unloading of your truck camper but could be used as stabilizing jacks along with the 3 existing jacks on your camper to help support and hold…

view full answer...

Answer 5

If it were me I would go with the taller 67 inch Brophy jacks part #CJ74. Having more height than needed would be better than not having quite enough. Plus your truck does sit taller than most similar sized trucks so the extra height would be…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

A tow package for a vehicle is usually a frame mounted trailer hitch and trailer wiring on a vehicle like your 2002 Dodge Dakota. If you have those two things you could pretty easily assume you have the tow package. Or, you can take the VIN of your…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

How to Order a Quantity of 4 Camper Jacks

Product Page this Question was Asked From

Continue Researching