How to Clear Out-of-Stroke Error Message on Lippert Ground Control System LC358590

Question

Question:

How do I reset the jack that is causing the problem

asked by: Ed

0

Expert Reply:

If you get the Out of Stroke error message on the Lippert Ground Control system, such as # LC358590, then that indicates that the jack has extended as far as it will go and cannot go any further.

To clear the error you can extend all of the jacks in the system at least 6 inches. Then press and hold the retract button until the jacks start to retract. All of the jacks should fully retract and the error should be cleared.

expert reply by: Adam R

0

Answer 1

I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast and the system won't reset. He…

view full answer...

Answer 2

I was able to find the service manual for the Lippert Ground Control 3.0 #LC358590 and found in that where Lippert recommends if the jacks are down for extended periods, it is recommended to spray exposed leveling jack tubes with lubricant every 3…

view full answer...

Answer 3

I spoke to the Manufacturer and this is a common problem when a wire is grounding out or there is a connection failure. If you follow the wires on your jacks part #LC358590 back to the battery and there is no bare wire, it's possible the main…

view full answer...

Answer 4

If you get the Out of Stroke error message on the Lippert Ground Control system, such as #LC358590, then that indicates that the jack has extended as far as it will go and cannot go any further. You might be able to solve this issue by raising the…

view full answer...

Answer 5

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 6

The left front jack error code ("LF) you are getting on your Lippert Ground Control System like #LC675817 can be triggered by a few different things. The first, which it seems you may have already ruled out, is that the system is for whatever…

view full answer...

Answer 7

I spoke with my contact at Lippert and he informed me that the lights flashing indicate the low point of the coach and that if you perform a zero point calibration you will correct that. In the service manual you will need to follow the instructions…

view full answer...

Answer 8

The Lippert Landing Gear Leg model LCI PN241846 on your landing gear system refers to the Lippert Heavy Duty Landing Gear Master Leg #LC241846. For a repair kit that will work nicely with this leg, you can use the Lippert Lead Leg Repair Kit…

view full answer...

Answer 9

The 241845 actually comes back to the Replacement Heavy-Duty Landing Gear Jack Leg #LC241845 which is the replacement leg for the Ground Control 2.0 which does not have a gear repair kit available so you would need to replace the leg with a new…

view full answer...

Answer 10

The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set #LC675817 does require adequate power to work properly. I recommend checking your ground connection from your battery to the trailer frame and…

view full answer...

Answer 11

To prevent theft of your Portable Power Watchdog Surge Protector with Bluetooth #HU97FR you can run the Master Lock Python Cable Lock #8419DPF through the metal holder on the cable (pictured below) and around the power pedestal.

view full answer...

Answer 12

Yes, you can replace your Dometic rooftop AC unit (condenser unit) with a Furrion one and still be able to use your existing thermostat and wiring. You just may need an adapter #ACCOLKIT to go from the wiring harness on the Furrion unit to the…

view full answer...

How to Clear Out-of-Stroke Error Message on Lippert Ground Control System LC358590

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching