Wire Gauge of Sealed, 3-Light Truck, Trailer Identification LED Light Bar # MCL93RB

Question

Question:

What are the wire gauge sizes on this LED light bar?

asked by: Brian

0

Expert Reply:

The wire gauge of the Sealed, 3-Light Truck, Trailer Identification LED Light Bar # MCL93RB that you referenced is 16 gauge.

expert reply by: Jameson C

0

Answer 1

The Optronics 4-Way Wishbone Trailer Wiring Harness #A25W2GWB that you referenced has 18 gauge wire for the ground and 20 gauge wire for all of the lighting functions. I check with all of the other wishbone harnesses that we have and they all use…

view full answer...

Answer 2

The Optronics 25 foot 4 Way Wire Harness #A25W2GWB will be a good option. This will generally have enough length to cover most trailers. I will also recommend adding in a few of the Spectro Self-Stripping Connector with Waterproof Sealant…

view full answer...

Answer 3

There isn't specific hardware designed for Sealed, 3-Light Truck, Trailer Identification LED Light Bar, Black Base, 50" Lead, 9 Diode -Red Item #MCL93RB. You would use hardware appropriate for the mounting surface the light will be attached…

view full answer...

Answer 4

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 5

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 8

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Answer 9

We have a great option in a replacement 45 amp power converter for your ELX-45. I suggest the Progressive Dynamics, #PD4045KA. This is a 2-in-1 AC/DC distribution panel and smart charger that works with lithium-ion, flooded lead acid, AGM, and gel…

view full answer...

Answer 10

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 11

The Hopkins Endurance Easy-Pull Harness part #HM38136 uses 18 gauge wire for all but the ground circuit and it comes with a 25' long lead therefore it will max out at around 5 amps or 60 watts.

view full answer...

Answer 12

Connecting the brown running light wire in standard 4-pole wiring to both tail lights will require a jumper wire from one side of the trailer to the other, or you can install what's called a wishbone harness that has dual brown running light…

view full answer...

Wire Gauge of Sealed, 3-Light Truck, Trailer Identification LED Light Bar # MCL93RB

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching