Recommended Shock Absorber For 5th Wheel Trailer With Tandem Axles

Question

Question:

Hi, Im looking for shock absorbers for a 2003 Montana Fifth Wheel 3655FL. I think the Dexter number was 052-003-00. Do you have something suitable?

asked by: David H

0

Expert Reply:

For the trailer suspension on your 2003 Montana 5th wheel, the closest replacement we have for your Dexter shock absorbers is the Lippert Components Heavy-Duty Replacement Shock # LC283280. This is not a direct replacement.

If you want further suspension assistance on your trailer, I recommend the E-Z Flex Heavy Duty Rubber Suspension System by Dexter Axle - 5-5/8" Equalizers # K71-652-00 for axle spacing 33 inches. If your axle spacing is 35 inches, I recommend the E-Z Flex Heavy Duty Rubber Suspension System by Dexter Axle - 7-3/4" Equalizers # K71-653-00.

expert reply by: Jason S

0

Answer 1

The 052-003-00 number on your current shock is the part number from Dexter Axle. We don't carry the direct replacement but if the specs match for the Lippert Standard Replacement Shock #LC283271 and the axle this is being applied to is a…

view full answer...

Answer 2

In order to determine if the Lippert Replacement Shock #LC283271 will fit your 2001 Thor Wanderer, you will need to remove one of its current shocks and take a measurement. If it has a compressed length of 7-1/2" and an extended length of…

view full answer...

Answer 3

I reached out to my tech contact at Lippert and the Standard Replacement Shock - Black #LC283271 doesn't have a rated capacity but is designed only for use on 2-3/8 inch diameter axles. That axle size is the 3,500 lb axle, so seeing as they are…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 9

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Recommended Shock Absorber For 5th Wheel Trailer With Tandem Axles

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching