Recommended Replacement Tail Light Assemblies for a Yamaha Trailer

Question

Question:

I have a 2004 MFi 23 foot trailer model # ymh230-g I need both tail light replacements - preferably in LED Can you advise which would fit this application? Thanks

asked by: Mike

0

Expert Reply:

If your Yamaha trailer measures over 80 inches, then I recommend the Optronics Waterproof LED Trailer Light Kit, # TLL160RK. This light set is designed for marine trailer applications which means the unit is sealed and waterproof. The units are hard wired to your current trailer's lighting wiring and the units have separate ground wires.

For a trailer that is smaller than 80 inches, I recommend the Optronics Micro-Flex LED Trailer Tail Lights, # STL28RB & # STL29RB. These light are square in shape and are sealed to make them waterproof and submersible.

expert reply by: Jared P

0

Stephen H.

5/10/2020

I like the LED light but I need it 6" x 3 1/2" for Roughneck Trailer. Let me know what you have.

Reply

Chris R.

5/13/2020

The Optronics LED Tail Light Kit # TLL56RK is perfect for you. These assemblies measure 6-1/16" wide and 3-5/8" tall (the closest to 6 x 3-1/2 we have available).

Reply

Answer 1

It is not recommend to jack up a trailer by the axle. This may cause damage to the axle itself. It also puts too much stress on the leaf springs. Instead, you will want to place the jack under part of the trailer frame preferably next to the leaf…

view full answer...

Answer 2

I recommend using 40 Ft 5-Way Trailer Wiring Harness #A40W5B, which is a kit that will replace your entire 5 way boat wiring setup and give you the 5 way connection at the front of the trailer. The lighting wires are 40 feet long, which will be more…

view full answer...

Answer 3

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 4

I recommend replacing an entire ladder if it's damaged. You'll want to find a replacement based on the height. Such as the Stromberg Carlson #LA-401 that is 99-1/2 inches tall. They can be cut shorter to customize the length if needed.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Between the Kuat Transfer part #KU74FR and the Swagman Chinook part #S64683 I would go with the Transfer mainly because it only touches the bikes at the tires whereas the Chinook grabs the frame of the bikes when securing. Swagman and Kuat are both…

view full answer...

Answer 7

The Thule WingBar Evo Crossbar System part #TH711520, part #TH480R, and part #THKIT1803 while installed on your 2019 Toyota Highlander will indeed need to be positioned so that the door clip is located 13-1/4" back from the rubber molding…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Recommended Replacement Tail Light Assemblies for a Yamaha Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching