Drum and Hub Kit, Wheel, and Brake Assembly Recommendation for a 2009 Starcraft 2106
Question:
I wish to put on trailer brakes on my 2009 Starcraft 2106. The axle is made by Dexter I think and do not know its model. I removed one hub and measured with a cheap caliper and got the following measurements of spindle Seal size 1.73, model #TCM 171255TB, inner bearing 1 3/8, outer bearing 1 1/16 model L44649. My axle also has the ez lube grease fitting. I have 5.3 x 12 tires on it, and the GVWR is 2090 pounds. The axle has the brake mounting plate. I would like to bolt on a drum and hub kit and the brake assembly and keep my existing wheels. I think I need the 3500 pound drum assembly to fit with the bearing and seal sizes, but that will need a 10 drum. Im wondering if the 10 drum will fit my 12 wheels or if there is another option?
asked by: Blair
Expert Reply:
I did some research and found that all of the hub and drum assemblies that would fit on your spindle would be 10 inches in diameter, and I also found that if you have a 10 drum you have to have at least a 13 inch rim, so you would need to upgrade to bigger wheels and tires also.
The Trailer Hub & Drum Assembly, part # AKHD-545-35-EZ-K, that you referenced is the correct hub and drum assembly.
For brake assemblies I would recommend a Galvanized 10 inch Marine Brake Assembly, part # 18788, for the left hand assembly, and part # 18787 for the right hand side.
For bigger wheels and tires I would recommend that you get Karrier ST175/80R13 Radial Trailer Tire with 13 inch Galvanized Wheel - 5 on 4-1/2 - Load Range D, part # AM31994.
I attached a couple links to videos on installing brakes on a trailer that does not have brakes on them for you to check out also.
Products Referenced in This Question
Demco Hydraulic Drum Brake Assembly - Single Servo - Galvanized - 10" - Right Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Hydraulic Drum Brakes
- RH
- 3500 lbs
- Brake Assembly
- Single Servo
- 10 x 2-1/4 Inch Drum
- Demco
more information >
Demco Hydraulic Drum Brake Assembly - Single Servo - Galvanized - 10" - Left Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Hydraulic Drum Brakes
- LH
- 3500 lbs
- Brake Assembly
- Single Servo
- 10 x 2-1/4 Inch Drum
- Demco
more information >
Karrier ST175/80R13 Radial Trailer Tire with 13" Galvanized Wheel - 5 on 4-1/2 - Load Range D
- Trailer Tires and Wheels
- Tire with Wheel
- Radial Tire
- Load Range D
- 175/80-13
- 13 Inch
- M - 81 mph
- 5 on 4-1/2 Inch
- Steel Wheels - Galvanized
- Boat Trailer Wheels
- Kenda
more information >
Product Page this Question was Asked From
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Components for Off-Road Trailer Similar to Chevy Colorado Wheels
- Article: How to Charge a Dump Trailer Battery
- Q&A: Replacement Hub for 2013 Wildwood 26TBSS Hub Drum with AL-KO 8700
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Q&A: Replacement for Demco Master Cylinder 05680-C for Drum Brakes
- Q&A: Recommended Lithium Battery Compatible Power Converter For Parallax 7355
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Q&A: Replacement Hubs and Brake Assemblies for Dexter Mobile Home Axle and 8-147 Hubs
- Article: Most Popular Wheel Bearings
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: What is Boondocking
- Article: Cleaning Your RV Black Water Tank in 4 Easy Steps