Will Trailer Hub and Drum Assembly # AKHD-545-35-K Work On EZ Loader Trailer
Question:
Hi - I have an EZ Loader with 10inch hydraulic drum brakes. I can find no make on the axle so it must just be an EZ Loader part. Would these drums work? My drums appear to be 5 on 4 1/2 as well.
asked by: Ron
Expert Reply:
The bolt pattern of the # AKHD-545-35-K is a 5 on 4-1/2, but you will need to know what size your spindle is on your trailer to make sure the drums will work.
The easiest way to see what you need is to pull the hub and drum and get the numbers off of the bearings. It will be stamped or etched on the side of the bearing as shown in the attached photo. If you cannot find the numbers you will need to use a digital caliper like part # PTW80157 and measure the spindle where the bearings ride and also the inside diameter of the hub.
The # AKHD-545-35-K comes with the bearings, races, grease seal, grease cap, and lug nuts included. The inner bearing is # L68149 and the outer is # L44649 . The inner race is # L68111 and the outer is # L44610. The grease seal is # 58846.
Products Referenced in This Question
Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.719 Inch I.D.
- 2.565 Inch O.D.
- etrailer
more information >
Replacement Race for L44643 and L44649 Bearings
- Trailer Bearings Races Seals Caps
- Races
- Standard Races
- 1.980 Inch O.D.
- Bearing L44643
- Bearing L44649
- Race L44610
- 2000 lbs Axle
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Replacement Race for L68149 Bearing
- Trailer Bearings Races Seals Caps
- Races
- Standard Races
- 2.361 Inch O.D.
- Bearing L68149
- Race 68111
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
4" Carbon Fiber Digital Caliper
- Hand Tools
- Measuring and Layout Tools
- Digital Calipers
- Carbon Fiber
- Performance Tool
more information >
Product Page this Question was Asked From
Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: How to Add Tension to Solera Slide-Topper
- Article: Best Bike Racks for Electric Bikes
- Article: Trailer Wiring Diagrams
- Q&A: Correct Replacement for AL-KO 7230 Hub/Drum and Brakes
- Q&A: Solution for Squeaky/Noisy Trailer Suspension with Equa-Flex Equalizers
- Q&A: Is It Possible To Replace Fabric On Slide Out Awning?
- Article: Calculating Portable Generator Power Needs
- Article: Performance Chips and Modules
- Q&A: Solution for Needing Stoplight Circuit on Difficult to Find Vehicle
- Q&A: Do I Need To Have A 3-Wire to 2-Wire Converter To Flat Tow a 2022 Ford F-150?
- Article: Most Popular Wheel Bearings
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: How to Measure a Trailer Axle