Recommended Replacement Speedknob And Wedge Assembly For Yakima Ridgeback 4 Bike Rack

Question

Question:

The Red tightening handle does NOT engage the screw drive.Cannot tighten Yakima Ridgeback 4 Help.

asked by: George B

0

Expert Reply:

It sounds like you have a stripped threading in your Yakima Ridgeback 4 # Y02458. I recommend the Replacement SpeedKnob and Wedge Assembly for Yakima Bike Racks # 8880508. This will solve that issue for you and allow you to secure your rack. This comes with the control key for you to change out your lock cores to use what you have currently installed.

expert reply by: Jason S

0

Answer 1

If the knob of the Replacement SpeedKnob and Wedge Assembly for Yakima Bike Racks #8880508 spins freely that means it is locked. You'd need to insert the change key that came with this into the old lock core from your rack to install it in this…

view full answer...

Answer 2

The Yakima RidgeBack 4 Bike Rack #Y02458 has a SpeedKnob at the bottom that is designed to spin freely when it's locked and have the friction needed to loosen/tighten the bike rack when it's unlocked. It sounds like the opposite is happening…

view full answer...

Answer 3

If you look at the provided diagram, you can see the replacement parts that Yakima offers for your Ridgeback Bike Rack. If what you're needing isn't shown, please let me know what you're needing. Zip strips #Y8890297 Endcap #8890306…

view full answer...

Answer 4

We have just what you need for your Yakima FullTilt 5 bike rack. The part you need is the #8880508 which is the replacemenet speedknob and wedge assembly that includes a change key to swap out your old lock core and install it in this. If you can get…

view full answer...

Answer 5

Your Yakima RidgeBack 2 Bike Rack uses a SpeedKnob that tightens the rack inside your trailer hitch receiver. Before removing the hitch pin and the bike rack, you will need to turn and loosen this knob so the shank can slide out of the receiver. To…

view full answer...

Answer 6

I checked with Yakima and the only way to get the wedge for the Yakima Ridgeback is with the part #8880508

view full answer...

Answer 7

The wedge you are seeking is only available in the Replacement SpeedKnob and Wedge Assembly for Yakima Bike Racks #8880508. Yakima doesn't offer just the wedge as a separate piece.

view full answer...

Answer 8

I do have an option for you but the Replacement SpeedKnob and Wedge Assembly part #8880508 will not work with the Yakima DoubleDown Ace 2, 4, or 5. In order to replace the knob and lock you will need to use the Replacement Tongue Assembly part…

view full answer...

Answer 9

The part you are looking for is the Replacement SpeedKnob and Wedge Assembly for Yakima Bike Racks #8880508. This will allow you to replace any SpeedKnob and anti-rattle wedge assembly on your Yakima RidgeBack #Y02457.

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Recommended Replacement Speedknob And Wedge Assembly For Yakima Ridgeback 4 Bike Rack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching