Brake Controller Will Work When Using Manual Override Lever But Not When Pressing Pedal

Question

Question:

I have the same issue that I see other people have had. The manual brake override works the trailer brakes but not the brake pedal. Could it be there is a fuse on the vehicle side thats blown? I have a 2007 GMC Sierra

asked by: Randy

0

Expert Reply:

Usually, when your brake controller works using the manual override and on when pressing the pedal, the issue is with the red wire connected to the stop light switch.

Using circuit tester, like # PTW2993, check to see if you have any electrical signal on the red wire present when the brake pedal is pressed. If you have no power, check to make sure that the wire has not come loose from the connection on the stop light switch. The red wire is connected to the cold side of the stop light switch wiring. If your brake controller red wire is not connected to the correct wire, or is loose or broken, this would cause the problem you are experiencing.

However, if the red wire circuit checks out, the issue is most likely a faulty brake controller, and you will need to replace the unit.

There should not be a fuse on either blue or red wire circuit of your controller. The amount of amperage that these two circuits draw is very small and insignificant. Also, a fuse installed in line could cause trailer brake failure when in use.

expert reply by: Jared P

0

Answer 1

The correct torque for installing lug nuts on your 5 X 8 trailer's 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Brake Controller Will Work When Using Manual Override Lever But Not When Pressing Pedal

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching