What Size Drill Bit is Used When Installing Curt Trailer Hitch Part # C13206

Question

Question:

Hi, What type of drilling bit do I need to install this hitch. Please let me know. thank you!

asked by: Michael B

0

Expert Reply:

To install the Curt hitch part # C13206 you will need to use a 7/16 inch drill bit designed for steel. I attached an install video for you to check out for this hitch that shows it installed on a 2017 Outback as well.

expert reply by: Jameson C

0

Answer 1

The best trailer hitch for your 2019 Subaru Outback Limited is the Curt #C13206 because it has the best bumper clearance among hitches that fit your car; this hitch is a fit for both the 2.5i Limited and 3.6R Limited. This Class III, 2" trailer…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver #C13206 you were looking at for your 2017 Subaru Outback Wagon weighs in at 36lbs. I included a video of the #C13206 being installed on a 2017 Subaru Outback Wagon for you to take a look at.

view full answer...

Answer 3

I have the perfect solution for you! Take a look at the Hopkins EasyLift #74211. I have linked a video showing how the EasyLift works. Since you currently have to get your knee involved to close the tailgate the EasyLift will be the best solution for…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What Size Drill Bit is Used When Installing Curt Trailer Hitch Part # C13206

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching