Where are the 4 Points of Sway Control in Equalizer Weight Distribution Systems

Question

Question:

Where exactly are all the 4 points of sway control? Two are obviously in the bar on the L bracket. Where are the other two? Thanks

asked by: Ann

0

Expert Reply:

A system with 4-point sway control such as Equal-I-zer hitch # EQ37100ET has the 2-point as mention above in the L-brackets and then also sway control where the spring bars mount in the head. In both cases the sway control is resisting movement side to side (sway) and in most cases can only be overcome by the force applied to the system from the vehicle making a turn (which is why you are still able to turn with the trailer).

expert reply by: Jameson C

0

Answer 1

The benefits of an Equal-I-zer hitch over the e2 is primarily the improved 4-point sway control of the Equal-I-zer. The 4-point sway control utilizes steel on steel friction at the arms as well as in the hitch head to stop sway. The e2's…

view full answer...

Answer 2

We carry two sockets that are typically used to install a trailer ball on to a hitch. The 3/4 inch drive 12 point socket, #ALL643216 is for an 1-7/8 inch nut will fit the 2 and 2-5/16 trailer ball nut.

view full answer...

Answer 3

Between the three you mentioned the Equalizer setup will be the best option. We haven't had the best luck with the Blue Ox systems, and the Steadi Flex by Reese isn't their top of the line system, whereas the Equalizer setups are…

view full answer...

Answer 4

We do offer a 1-7/8-inch socket #ALL643216 that fits a 3/4-inch drive socket wrench. Since hitch balls need to be torqued to a specific rating I suggest you use a calibrated 3/4-inch torque wrench to re-install the hitch ball. Proper torque is…

view full answer...

Answer 5

The B&W Continuum Weight Distribution System part #BW78FR per B&W, does have built-in sway control. That said, all weight distribution systems have some sway control as they provide friction at the connection point which will then in turn…

view full answer...

Answer 6

You can definitely use SumoSprings with a weight distribution hitch like your Fastway e2 #FA92-00-1000 on your 2016 Toyota Tundra. What you want to do is install the SumoSprings and then adjust your weight distribution set up, like you mentioned.…

view full answer...

Answer 7

I'll start out by saying that the curb weight of the vehicle typically includes a full tank of gas and the driver of the vehicle (typically 150-lbs for the driver), so those shouldn't be included in your calculation. You're still going to…

view full answer...

Answer 8

Generally speaking, it is not advisable to reverse a trailer when using a weight distribution system. The system won't blow up but if you reverse at too sharp an angle then you can damage the head so you have to do so in a pretty straight line or…

view full answer...

Answer 9

To avoid trailer sway you want the tongue weight to be 10 percent of the total trailer weight. Your best option is going to be to keep the tongue weight and total trailer weight under the capacities of your vehicle and aim for the tongue weight to…

view full answer...

Answer 10

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…

view full answer...

Answer 11

To be completely honest the sway control feature of the B and W Continuum part #BW78FR isn't nearly as advanced as the rest of the system. The advertised sway control of this system is in the head of the system between where the ball and the…

view full answer...

Answer 12

I would recommend using the exact procedure you outlined. Tighten the shank bolts first and then with the shank in the vehicle hitch (secured with hitch pin) torque down the hitch ball to 450 ft lbs.

view full answer...