Needing Air Spring Spacers That Will Work on a Vehicle With a 2 Inch Lift

Question

Question:

Hello, I have a 2008 Dodge Ram 1500 4x4 with an Air Lift 5000 air bag installed. My question is will the Lift Spacers for Firestone Ride-Rite Air Helper Springs - Vehicles w/ 2inch Lift Item # F2366, fit on my Air lift and truck set up. Thank you.

asked by: Brad

0

Expert Reply:

I have a solution for you. Unfortunately, the Firestone # F2366 are not designed to work with the Air Lift air springs.

Air Lift has part # AL52420 which is for a 2 inch lift.

They're made of steel and work with the LoadLifter kits like what you have.

expert reply by: Jared P

0

Answer 1

The 2 inch lift Air Lift Universal Air Spring Spacers for LoadLifter 5000 and 7500XL #AL52420 have a diameter of approximately 4-1/2 inches. They are designed to not only work with the Air Lift LoadLifter 5000 and 7500XL but you can also use them…

view full answer...

Answer 2

Yes, the Air Lift Spring Spacers for LoadLifter Air Helper Springs part #AL52420 will work with Firestone Ride Rite Air Helper Springs.

view full answer...

Answer 3

If the lift you installed added height to the suspension between the frame and the axle you would need a 2 inch spacer when installing the part #AL57204 with the part #AL52420 which will take up the extra space created. Since you asked where it…

view full answer...

Answer 4

Your tandem axle trailer's equalizers handle the task of evening out the load across the two axles. I noted that in your photo the axles appear to have different tires installed on each. It is best to use identical tires on both axles, meaning…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Needing Air Spring Spacers That Will Work on a Vehicle With a 2 Inch Lift

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching