Brushed Nickel Dual Handle RV Tub Diverter Faucet with D-Spud

Question

Question:

Would you have a Phoenix brushed nickel 2 handle tub diverter faucet with D-spud? R4763 I see you have a chrome tub diverter, but had my heart set on a brushed nickel

asked by: Ruth M

0

Expert Reply:

In brushed nickel, D-spud we have Phoenix Faucets # PF223461. The knobs are a little different though. I have linked a video review of this faucet for you.

expert reply by: Michael H

0

Answer 1

There is a slight amount of play in the downspout on the Phoenix Faucets 4" Dual Handle RV Tub/Shower Diverter Faucet part #PF213332. It appears as if it was just nudged to one side during the demo video you are referring to but I can assure you…

view full answer...

Answer 2

Yes, the Flow Max RV Fresh Water Pump #LC689052 will be a good replacement for your Shurflo 2088-422-144 water pump on your camper. This pump can be used as a replacement for any OEM water pump so it will work out perfectly for you. I have added a…

view full answer...

Answer 3

We have a direct replacement for your OEM 12-volt Shurflo 2088-422-144 fresh water pump, HydroMax RV Fresh Water Pump #P25201. The pump delivers 3-gallons per minute at 55-psi and will draw 10-amps maximum current. It includes a built-in strainer and…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Brushed Nickel Dual Handle RV Tub Diverter Faucet with D-Spud

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching