Replacement Wheel Stud For Dexter 7000 lb Axle With 8 Lug Hub Assembly

Question

Question:

i have a dexter 7k 8 lug axle and need the studs . can you give me the link for the right studs and also need the nuts

asked by: Mario

1

Helpful Expert Reply:

For 7,000 lb Dexter hub assemblies, you could have 1/2 inch or 9/16 inch, or 5/8 inch drive in studs. I've linked the page of our drive in wheel studs for you. Once you have the right stud based on your measurements you can get the correct lug to fit on the other linked page.

expert reply by: Jason S

1

Answer 1

We do have the correct wheel stud for your Dexter Trailer Hub and Drum Assembly #8-219-13UC3. This is a 9/16" bolt, and the correct replacement part is the following: - Drive-in Wheel Bolt for Trailer Wheel Hubs - 9/16" Diameter x…

view full answer...

Answer 2

BD2-655 is only a portion of the code for the hub so there are a few different options depending on the capacity of your hub. Your 2018 Grand Design Reflection 28BH most likely has 5.2k axles with hubs like part #AKHD-655-6-EZ-K, which has…

view full answer...

Answer 3

Hubs and drums that can be turned (machined) will have a specification on how much they can be turned cast into the metal of the drum somewhere. Otherwise it is at the brake shop's discretion. Drums do not have to be turned unless there is some…

view full answer...

Answer 4

So long as a hub uses the correct bearings that match the dimensions of the spindle that is on the axle there is no worry about using two different brands of products, such as a Dexter hub on a Lippert axle. That in itself is not a concern. When a…

view full answer...

Answer 5

Thanks for the information on your trailer. For your axle with brakes I recommend the Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb E-Z Lube Axles - 12" - 6 on 5-1/2 #AKHD-655-6-EZ-K if you have the spindles with the integrated grease…

view full answer...

Answer 6

We have many styles and sizes of trailer wheel lug nuts shown on the linked page. These are offered in either 60-degree or 90-degree coned profile, in zinc, chrome or stainless and for four different wheel stud diameters. Just click on the feature to…

view full answer...

Answer 7

If you take a look at the provided photo, you can see the important dimensions of the #TRU37FR spindle.

view full answer...

Answer 8

I went out to the warehouse to take some measurements of trailer spindle #TRU37FR for you. The stub is actually 3-3/8 inches from the end to the brake flange. It is 3 inches from the end to where the weld is for the brake flange. The brake flange…

view full answer...

Answer 9

First, I wish you good luck with your build project. No one eats without our farmers! Do please note that DOT regulations limit trailers to a width of no more than 103-inches for on-road use. If your trailer will see only agro use and never go on…

view full answer...

Answer 10

I believe you are looking for the correct nut to fit the stud part #007-112-00 which would be the #38N.

view full answer...

Answer 11

I do have an option for you but the Ford TPMS for Trailers only works with 15" and smaller trailer wheels due to the valve stem hole size of .452" they use. The valve stem hole size on a 16" and larger trailer wheel like the Westlake…

view full answer...

Answer 12

Trailer spindles are welded directly to the axle so to remove one it just needs to be cut off completely using a torch or saw. Then to replace the spindle such as with the EZ Lube #TRU37FR that you were looking at it's extremely important that it…

view full answer...

Replacement Wheel Stud For Dexter 7000 lb Axle With 8 Lug Hub Assembly

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching